I will select a smartphone as the device of my preference.
Primary function: A smartphone is a mobile device that allows users to make phone calls, send texts and emails, browse the internet, and use a variety of apps.
Design requirements:Durability: The device should be able to withstand everyday wear and tear, such as being dropped or bumped.
Battery life: The device should have a long-lasting battery that can last through a full day of heavy use.
Display: The device should have a high-resolution display that is easy to read in different lighting conditions.
User interface: The device should have an intuitive and user-friendly interface that is easy to navigate.
Read more about smartphones here:
https://brainly.com/question/25207559
#SPJ1
if a body is subjected to a coplanar system of loading, which internal resultant loading component is zero at the section obtained by the method of sections?
In the case of a coplanar system of loading, the internal resultant loading component at the section produced by the method of sections is zero. When cutting the piece for the coplanar loading method, there will be
What is coplanar door?
Coplanar refers to two surfaces that are installed absolutely flush with one another and signifies "put on the same plane." This is the leaf in relation to the architraves in our case, or
The MFU is a simple-to-install sliding door system that enables a door to close "flush" against the surrounding walls, giving it a neat and inconspicuous appearance and, if you so want, virtually concealing the door! No bottom track is necessary, allowing for a flooring run that is unobstructed.
Know more about method, Visit:
https://brainly.com/question/30076317
#SPJ1
9.
The high collision rate for new drivers is primarily
because...
Answer:
immaturity, lack of skills, and lack of experience.
Explanation:
describe the three parts (sensor/transducer, signal conditioning, output stage) of the following measurement systems: a) measuring cup used in the kitchen b) system used to measure the gasoline pumped into a car at the gas station. if you have to look on the internet to see how these measurement devices work. if one of the three parts of a general measurement system do not exist in a) or b) then say so.
A measurement system is a system used to measure physical quantities and convert them into a form that is easier to read and interpret.
Measurement systemA) Measuring Cup Used in the Kitchen: Sensor/Transducer: A measuring cup typically has lines or markings on the inside that indicate the amount of liquid inside. This acts as the sensor/transducer because it converts the physical quantity of the liquid into a visual representation. Signal Conditioning: Not applicable.Output Stage: Not applicable.B) System Used to Measure the Gasoline Pumped into a Car at the Gas Station: Sensor/Transducer: The sensor/transducer in this system is typically a flow meter. It measures the rate of flow of the gasoline as it is pumped into the car.Signal Conditioning: The signal from the flow meter is conditioned by the gas pump computer. It filters out noise, amplifies the signal, and converts it into a signal the computer can understand.Output Stage: The output stage of this system is the display at the pump, which displays the amount of gasoline pumped and the cost.To learn more about measurement system refer to:
https://brainly.com/question/105317
#SPJ4
Measurement system, any of the systems used in the process of associating numbers with physical quantities and phenomena.
What’s the purpose of things?• A)Measuring Cup for Kitchen Use: Sensor/Transducer: A measuring cup usually contains lines or markings on the inside to show how much liquid is inside. This functions as a sensor/transducer by converting the physical quantity of liquid into a visual representation.
• B)Gasoline metered at the pump, system used at gas stations to monitor the amount of gasoline poured into an automobile. If you have to check up how these measurement equipment function on the internet.
Flow estimation
The gasoline pumped must be properly measured by the apparatus. Flow is nearly commonly measured using a four-stroke piston meter linked to an electronic encoder.
• Transducers and sensors ,A sensor and a transducer are both used to detect changes in the environment or an item to which they are attached. A sensor, on the other hand, will produce the same output format, and a transducer will turn the measurement into an electrical signal.
• Signal conditioning is a data collecting technique that is carried out with the help of a signal conditioner. This device transforms one sort of electrical or mechanical signal (input-signal) into another (output-signal).
• The fundamental goal of an operational amplifier’s output stage is to provide a given amount of signal power into a load while exhibiting acceptable levels of signal distortion.
To learn more about Measurement System to refer:
https://brainly.com/question/29379210
#SPJ4
calculate the distance d from the center of the earth at which the force on a particle from the moon is equal to 1.24 times the force on the particle from the earth. The particle is restricted to the line through the center of the earth and the moon. Justify the two solutions (d1
To calculate the distance d from the center of the earth at which the force on a particle from the moon is equal to 1.24 times the force on the particle from the earth, we can use the equation Fmoon/Fearth = 1.24. This equation can be rearranged to Fearth = Fmoon/1.24.
Then, since Fearth = GMearthm/(d^2) and Fmoon = GMmoonm/(d^2), we can substitute in our equation to get GMearthm/(d^2) = GMmoonm/(1.24d^2). Solving for d, we get d = (GMmoon/1.24GMearth)^(1/2).
This will give us two solutions, d1 and d2, which are the distances from the center of the earth to the two points at which the forces from the earth and moon are equal.
Learn more what is the distance:
https://brainly.com/question/26550516
#SPJ4
a parachutist of mass 68.1 kg jumps out of a stationary hot air balloon. compute velocity as a function of time. the drag coefficient is equal to 12.5 kg/s. (refer to class notes and textbook example) use f
The rate of change of position is defined as velocity. The velocity as function of time will be 53.44(1-e^-0.18355 x t)
What is velocity?
The displacement that is the shortest distance between an object's initial and final positions in a specific direction is defined as a change of position. Velocity is a linearly increasing function of time, with a straight line passing through it. The velocity versus time curve must be linear and have the same slope as the acceleration.
v = 53.44(1-e^-0.18355*t)
I understand that my initial values are as follows:
x(0)=0
y(0)=0
h=2
x(f)=12
where x is t and y is v.
Therefore the solution will be :
t(s) v(m/s)
0 0.00
2 16.42
4 27.80
6 35.68
8 41.14
10 44.92
12 47.54
∞ 53.44
To learn more about velocity refer to :
brainly.com/question/25749514
#SPJ4
(Multiple Choice) Which of the following is most likely to be considered an overarching goal of the International Society of Technology in Education (ISTE) standards?
a. To enable teachers to create dynamic learning experiences that integrate our understanding and the relevance of technological tools that provide educational support.
b. To provide roles for government and professional organizations in the development of standards.
c. To introduce computers and technology into the classroom.
d. To create consequences for compliance and noncompliance for use of technology in the classroom.
The International Society for Technology in Education (ISTE) Standards for Learning, Teaching, and Leading in the Digital Age provide us with a comprehensive roadmap for effective use of technology in schools around the world.
What is ISTE Standards?The International Society for Technology in Education (ISTE) Standards, formerly known as the National Educational Technology Standards, are guidelines for using technology in teaching and learning. The International Society for Technology in Education, a nonprofit membership organization for educators focused on educational technology, publishes them.ISTE teacher standards place high expectations on technology educators. These standards prepare teachers to teach advanced concepts and technology in the classroom. It also encourages teachers to share ideas for engaging their students with one another.These standards include learning how to be responsible and safe online, understanding and applying computational thinking, effectively curating and evaluating digitally acquired knowledge, and successfully communicating with others using digital tools.To learn more about ISTE standard refer to :
https://brainly.com/question/14587213
#SPJ4
in order to generate findings about causation, researchers must use research. correlational experimental observational naturalistic
In order to generate findings about causation, researchers must use experimental research.
What is the difference between correlational and experimental research? Correlational research is a type of research that looks at the relationship between two or more variables. It seeks to identify the correlation, or relationship between the variables, without making any assumptions about cause and effect. Correlational research is used to find out if there is a relationship between two or more variables, and if so, what is the strength of the relationship. This type of research does not allow us to make conclusions about cause and effect.Experimental research is a type of research that looks for cause and effect relationships between two or more variables. It involves manipulating one variable to observe the effect on another variable. Experimental research allows researchers to make conclusions about cause and effect relationships, as it allows them to control the environment and look for changes in the dependent variable. Experiments are often used in the natural sciences, such as biology and psychology, but can also be used to study social and economic phenomena.To learn more about experimental research refer to:
https://brainly.com/question/17009178
#SPJ4
smoking bans and motor-vehicle restraint laws are examples of
Answer:
Smoking bans and motor-vehicle restraint laws are examples of public health and safety regulations.
Direct-tension tests use what kind of test
specimens? Select all that apply.
A. Cross-tension specimens
B. Longitudinal fillet weld specimens
C. U-shaped specimens
D. Round tensile specimens
Direct-tension tests use the kind of test specimens known as D. Round tensile specimens
What is a Direct-tension test?A direct-tension test, also known as a tension test or a tensile test, is a type of mechanical test used to determine the material's strength and behavior under tension loads.
The test specimen is typically a cylindrical or round shape and is placed in a tensile testing machine. The machine applies a load to the specimen in one direction, stretching it until it fractures.
The load, elongation, and other data are recorded during the test, and from these data, the material's properties such as ultimate tensile strength (UTS), yield strength, and modulus of elasticity can be determined.
Read more about Direct-tension tests here:
https://brainly.com/question/29843307
#SPJ1
The focus of these problems will be working with information extracted from a
municipal government data feed containing bids submitted for auction of property.
The data set is provided in two comma-separated files:
1. eBid_Monthly_Sales.csv (larger set of 17,937 bids)
2. eBid_Monthly_Sales_Dec_2016.csv (smaller set of 179 bids)
This assignment is designed to explore hashing algorithms by implementing a hash with chaining of collisions for bids loaded from a CSV file.
We provide a starter console program that uses a menu to enable testing of the sort logic you will complete. It also allows you to pass in the path to the bids CSV file to be loaded, enabling you to try both files. In this version the following menu is presented when the program is run:
Menu:
1. Load Bids
2. Display All Bids
3. Find Bid
4. Remove Bid
9. Exit
One form of completely automated advertising is smart display campaigns. Remember that your desired ROAS may have an impact on the umber of conversions you receive.
Target CPA bidding is a Smart Bidding technique that automatically sets bids to increase conversions (customer actions). You specify an average cost for each conversion when creating the Target CPA (target cost-per-action) bid strategy. The average conversion value (such as revenue) that you would hope to receive for each dollar spent on us known as the target ROAS. Remember that your desired ROAS may have an impact on the umber of conversions you receive. For instance, if you set your objective too high, fewer individuals may see your advertisements. If Paul has confidence in his capacity to create bids on his own, he can rely on the Smart Display campaign.
Learn more about Target ROAS here:
https://brainly.com/question/29697386
#SPJ4
technician a says a rotor pump has a center rotor that is driven by the torque converter. technician b says a vane pump has a center gear that drives an outer gear. who is correct?
The technician in A is right. Because a gear's transmission is utilized to enhance or decrease torque, Technician B is mistaken.
The relationship between torque and circumferential detail depends on how the radius is used as a resource; larger gears experience more torque, while smaller gears experience significantly less torque. The ratio of the radii of the gears and the torque ratio are also identical. The transmission torque of a gear changes as its speed increases or decreases. A tiny torque on the entryway problem is frequently transferred as a large torque at the output problem by using the resource of lowering the speed. The use of a wide variety of teeth as a resource allows for the quantification of torque.
Learn more about Torque here:
https://brainly.com/question/28965370
#SPJ4
this sign is used to warn drivers about: this sign is used to warn drivers about: upcoming intersections. road construction. road curves ahead. 31 . when you see this sign, you sho
The route's right-hand curve is described by the road sign in figure A. The driver uses roadside signage to navigate the area gently and securely.
To help users become aware of the situation, signs are placed at various sites and on roads. The driver uses roadside signage to navigate the area gently and securely. The road ahead is curved to the right, hence the supplied sign in the illustration reads "A." Option C is right as a result. The route's right-hand curve is described by the road sign in figure A. Option C is right as a result. The best response to the query "Orange Road sign" is option C. (Road construction). The orange road sign warns motorists that there may be construction up ahead. Most driving schools inform aspiring drivers about traffic signs and assist them in understanding their meaning.
Learn more about Roadside signage here:
https://brainly.com/question/4839651
#SPJ4
p1 - connecting computing consider the following program, which is intended to display the number of times a number target appears in a list.
The program correctly displays the number of times target appears in the list. The program correctly keeps track of the number of times that the target appears in the list and displays this number.
What is the purpose of the code?The purpose of this code is to count the number of times a specified target appears in a given list. The code begins by setting the initial count to 1. This is followed by a "For Each" loop, which iterates over each element of the list. For each element, the code checks if it is equal to the target. If so, the count is incremented by 1. After the loop finishes, the code displays the count, which is the number of times the target appears in the list. This code can be used to quickly determine the frequency of a particular number or value in a list, making it easier to analyze and visualize the data.To learn more about purpose of code refer to:
https://brainly.com/question/30032849
#SPJ4
1. A steel container expands in volume 1% when the pressure with in it is increased by 70Mpa. At standard pressure, it holds 8kg of water; =1000kg/m3. For K=2.05Gpa, when it is filled, how many kilograms of water must be added to increase the pressure to 70Mpa (gage)?
19 kg of water would be needed to increase the pressure in the steel container to 70 MPa. This was carried out with Pressure-Volume Water Calculation
Steps in CalculationTo calculate the amount of water needed to increase the pressure in the steel container by 70 MPa, we can use the formula:
V1 = V0 (1 + (K * P1) / P0)
Where:
V1 = final volume of the container
V0 = initial volume of the container
K = coefficient of volumetric expansion (2.05 GPa)
P1 = final pressure (70 MPa)
P0 = initial pressure (0 MPa)
We know that at standard pressure, the container holds 8 kg of water, so the initial volume can be calculated as:
V0 = 8 kg / (1000 kg/m^3) = 0.008 m^3
We can use this information to calculate the final volume of the container when the pressure is increased to 70 MPa:
V1 = 0.008 m^3 (1 + (2.05 * 10^9 Pa * 70 MPa) / (0 MPa))
V1 = 0.008 m^3 (1 + (143.5 * 10^6 Pa) / (0 MPa))
V1 = 0.008 m^3 (1 + 1.435)
V1 = 0.008 m^3 * 2.435
V1 = 0.019 m^3
To calculate the amount of water needed to fill the container to this final volume, we can use the density of water:
mass = V1 * density
mass = 0.019 m^3 * 1000 kg/m^3
mass = 19 kg
So, 19 kg of water would be needed to increase the pressure in the steel container to 70 MPa.
Learn more about Pressure-Volume calculation here https://brainly.com/question/20461483
#SPJ1
Design a database for an online assignment management system (think of it as Canvas with only assignment management features):
Requirements:
The system should be able to store and manage professor/student accounts, courses, assignments, submissions, grades, comments, and track email notification's delivery status.
Professors are able to create and manage their courses (a professor can create multiple courses but one course can be owned/managed by only one professor).
Students can enroll in multiple courses.
For each course, multiple assignments can be created.
A student can submit multiple times for an assignment. All the submissions will be saved but he will be graded only once.
Students and professors can leave comments on assignments (like the Canvas system).
To make sure comments are read in time, when a new comment is added, the system will notify the other party right away by email.
In order to guarantee all email notifications are successfully delivered, the system needs to track and resend failed email delivery attempts (this is necessary as sometimes the target mail server could be temporarily down or offline or under maintenance).
Online Project and Assignment Submission, Management and Progress Monitoring System (OPAS) is a system that enables the student to submit their assignment or project online without sending any physical files.
How do you manage assignments?A piece of software known as an assignment management system assists teachers in setting up task schedules and allocating tasks to specific pupils. The teachers also give the pupils deadlines, and after they submit their work, they assess it.Online Project and Assignment Submission, Management and Progress Monitoring System (OPAS) is a system that enables the student to submit their assignment or project online without sending any physical files.Online Project and Assignment Submission, Management and Progress Monitoring System (OPAS) is a system that enables the student to submit their assignment or project online without sending any physical files.The complete question is,
What is a system for electronically submitting assignments?
To learn more about assignment management system refer to:
https://brainly.com/question/13444413
#SPJ4
b. draw the equivalent circuit of the alternator per phase under the dc field excitation conditions given above. c. what is the nominal full load current per phase? 2. a. if the alternator in problem 1 supplies a resistive load of 120mw at a voltage of 12kv, what must be the induced voltage eo ?
The nominal and rated currents are same. When a motor is producing its rated mechanical output at its shaft, this is the current that it is drawing.
Explain about the nominal full load current?The maximum current that a given load can drain from the circuit is known as full-load current. The nominal current is the current at which efficiency will be at its highest. However, in most real-world scenarios, these are all the same; substituting the same value for each of these will have no effect.
The electrical voltage during typical operation as provided by the manufacturer or supplier is the nominal voltage of an electrical load or a voltage source (battery, generator, power grid). It is always the voltage's RMS value unless otherwise stated.
The amount of current a motor uses to generate its rated horsepower load at its rated voltage is known as the full-load amperes (FLA). NEC tables
To learn more about nominal full load current refer to:
https://brainly.com/question/16178536
#SPJ4
/* The constructor initializes a History object that corresponds to an Arena with nRows rows and nCols columns. You may assume (i.e., you do not have to check) that it will be called with a first argument that does not exceed MAXROWS and a second that does not exceed MAXCOLS, and that neither argument will be less than 1.*/
#include "history.h"
#include
using namespace std;
History::History(int nRows, int nCols){
m_rows = nRows;
m_cols = nCols;
for (int i = 0; i < m_rows; i++) {
for (int j = 0; j < m_cols; j++) {
m_grid[i][j] = false;
}
}
}
/*The record function is to be called to notify the History object that an unpoisoned rat has eaten a poison pellet at a grid point. The function returns false if row r, column c is not within bounds; otherwise, it returns true after recording what it needs to. This function expects its parameters to be expressed in the same coordinate system as the arena (e.g., row 1, column 1 is the upper-left-most position).*/
bool History::record(int r, int c){
if (r<1 || c<1 || r>m_rows || c>m_cols)
return false;
m_grid[r-1][c-1] = true;
return true;
}
/*The display function clears the screen and displays the history grid as the posted programs do. This function does clear the screen and write an empty line after the history grid; it does not print the Press enter to continue. after the display. */
void History::display() const{
clearScreen();
for (int r = 0; r < m_rows; r++){
for (int c = 0; c < m_cols; c++){
if (m_grid[r][c])
cout << "A";
else
cout << ".";
}
cout << endl;
}
cout << endl;
}
The constructor initializes a History object that corresponds to an Arena with nRows rows and nCols columns. You may assume (i.e., you do not have to check) .
What is grid?CSS Grid Layout is a two-dimensional layout system for the web. It lets you lay content out in rows and columns. It has many features that make building complex layouts straightforward. This article will explain all you need to know to get started with page layout.A grid is a collection of horizontal and vertical lines creating a pattern against which we can line up our design elements. They help us to create layouts in which our elements won't jump around or change width as we move from page to page, providing greater consistency on our websites.A grid will typically have columns, rows, and then gaps between each row and column. The gaps are commonly referred to as gutters.To learn more about grid refer to:
https://brainly.com/question/8370411
#SPJ4
A Windows computer is experiencing a problem accessing the Internet. The network patch cable and network interface card have been tested and verified to be working properly.
What step should be considered next to resolve this problem?
Question 5 options:
Update network settings.
Restart services.
Kill tasks.
Disable application startup.
Update network settings.
What Windows utility is particularly useful in identifying software and hardware bottlenecks, and provides the ability to monitor in real time?
Question 6 options:
Event Viewer
Reliability Monitor
Performance Monitor
Resource Monitor
A Windows tool called Resource Monitor allows for real-time monitoring and is particularly helpful in locating hardware and software bottlenecks. Users may view usage statistics for the areas of CPU, memory, disk, and network thanks to this display.
A Windows tool called Resource Monitor allows for real-time monitoring and is particularly helpful in locating hardware and software bottlenecks. By launching Task Manager and selecting the "Performance" option, you can get to it. Users may view usage statistics for the areas of CPU, memory, disk, and network thanks to this display. Additionally, it offers comprehensive details on each procedure or service and enables customers to track resource usage over time. Users that utilize Resource Monitor can quickly and efficiently troubleshoot problems by locating the bottleneck's origin. Additionally, it allows you to organize processes according to how much resource they are using and take the necessary steps, including terminating processes, preventing application launches, and altering network settings.
Learn more about software here-
brainly.com/question/29946531
#SPJ4
// quartstogallons.java class quartstogallons { public static void main(string[] args) { // write your code here } }
The alternative that can be utilized to change the /* missing code */ in order for the statement to compile correctly is.
List of years, The Java programming language is the subject of this query. As can be seen from the query, an ArrayList is involved. In Java, the syntax to declare an ArrayList with no specific data type is as follows: ArrayList [Name of the Lists] = new ArrayList(); The list name is now "years" in the query. Thus; The appropriate statement to replace any missing code in order to avoid mistakes is; ArrayList years is a replacement option that can be used to fill in any missing code, ensuring that the statement compiles successfully. Simply put, resizable arrays are ArrayLists. The statements (b) new ArrayList() and (c) I and III only are capable of substituting for the missing code, respectively. ArrayList creation syntax is as follows: new ArrayListType>() using the argument ArrayListType> str;
Learn more about ArrayList here:
https://brainly.com/question/29309602
#SPJ4
A bullet in a rifle accelerates uniformly from rest at 65 000 m/s2. If the velocity of the bullet as it leaves the muzzle is 450 m/s, (i) how long is the rifle barrel? (ii) How long did it take for the bullet to travel the length of the barrel? (iii) What is the average speed of the bullet?
The length of the rifle barrel will be about 0.69 cm. It took the bullet about 0.0069 milliseconds to travel the length of the barrel. And the average speed of the bullet is approximately 441.9 m/s.
(i) how long is the rifle barrel?
To find the length of the rifle barrel, we can use the equation:
length = (velocity^2 - initial velocity^2) / (2 * acceleration)
Plugging in the given values:
length = (450 m/s)^2 / (2 * 65 000 m/s^2) = 0.0069 m
So the length of the rifle barrel is about 0.69 cm.
(ii) How long did it take for the bullet to travel the length of the barrel?
To find the time it took for the bullet to travel the length of the barrel, we can use the equation:
time = velocity / acceleration
Plugging in the given values:
time = 450 m/s / 65 000 m/s^2 = 0.000069 s
So it took the bullet about 0.0069 milliseconds to travel the length of the barrel.
(iii) What is the average speed of the bullet?
To find the average speed of the bullet, we use the formula:
average speed = total distance / total time
Given that the bullet is accelerating uniformly, we can use the harmonic mean formula to find the average speed
average speed = 2 * length * velocity / (length + velocity/acceleration)
Plugging in the given values:
average speed = 2 * 0.0069 m * 450 m/s / (0.0069 m + 450 m/s/65000m/s^2) = 441.9 m/s
So the average speed of the bullet is approximately 441.9 m/s.
To learn more about rifle barrel, visit: https://brainly.com/question/14661669
#SPJ1
Clear statements of what students will achieve as a result of a lesson that they exhibit in an observable way. Also called learning outcomes.
Observable outcomes are the data sources and performance indicators, such as observations, artefacts, and dialogues, that allow for evaluation of the effectiveness of the remediation plan.
What is an example of observable learning?Both kids and adults can pick up new talents by watching others. Mom can teach a youngster how to do her nails, and films of others doing weightlifting can teach an adult how to do it.Anything you can observe another person doing is considered to be an observable activity. Walking, talking, sitting, singing, cuddling, eating, sleeping, solving math problems, and similar activities fall under this category.In order to represent what the learner will be able to perform as a result of the learning activity, learning objectives must be precise, observable, and measurable. They serve as benchmarks by which to assess advancement toward the accomplishment of the bigger objective.The value of observational learning is that it enables people, particularly youngsters, to learn new responses by observing how others behave.To learn more about Observable refer to:
https://brainly.com/question/854135
#SPJ4
if a twisted-pair cable has a diameter of 0.8 cm, which of the following options would you apply as the bend radius of the cable so that data transmission is not impaired?
The minimum bend radius for a twisted-pair cable with a diameter of 0.8 cm should be at least 3.2 cm. This ensures that the cable is not bent too sharply, which could impair data transmission.
When a twisted-pair cable is bent too sharply, the individual wires within the cable can be stretched or compressed, which can cause signal interference and impair data transmission. To prevent this, the bend radius of the cable should be at least four times the diameter of the cable. This ensures that the cable is not bent too sharply, which can cause signal interference and impair data transmission. For a twisted-pair cable with a diameter of 0.8 cm, the minimum bend radius should be at least 3.2 cm. This ensures that the cable is not bent too sharply, which can cause signal interference and impair data transmission.
Learn more about twisted-pair cable here
https://brainly.com/question/25337328
#SPJ4
Select below the name of the processor created by Intel for use in low-end desktops, netbooks, and laptops.
Intel Atom. Intel Atom is a processor created by Intel for use in low-end desktops, netbooks, and laptops. It is designed to be energy efficient and cost-effective, while still providing good performance.
It is typically used in devices such as netbooks, tablets, and other small form factor devices. It is also used in some embedded systems and industrial applications. Low-end desktops, netbooks, and laptops are computers that are designed to be affordable and have lower performance than more expensive models. They typically have slower processors, less RAM, and fewer features than more expensive models. They are often used for basic tasks such as web browsing, word processing, and other everyday tasks. A processor is a type of computer chip that is responsible for executing instructions and performing calculations. It is the main component of a computer and is responsible for carrying out the instructions of a computer program.
Learn more about Intel Atom here
https://brainly.com/question/29780027
#SPJ4
The y-component of the force F which a person exerts on the handle of the box wrench is known to be 87 lb. Determine the x-component and the magnitude of F
The force's x-component is 38.18 lb, while the force's magnitude is 93.16 Fy and the force F applied to the box wrench's handle is 86 lb.
Determine the x-component ?The force's x-component is 38.18 lb, while the force's magnitude is 93.16 Fy and the force F applied to the box wrench's handle is 86 lb.
Taking into account the triangle in Fig.
Perpendicular magnitude is equal to P = 12.
Base magnitude is B = 5.
Pythagoras's theorem is used
H = √P² + 5²
H = 13
12/13
y-component of force is given given as:
F= 86*(13/12)
F = 93.16 l b
F ( X) = 38.18 lb
To learn more about x-component refer
https://brainly.com/question/14284964
#SPJ4
engineers are tasked with designing a new solar system themed roller coaster ride. the track starts at point p, at the top of a sphere with radius r (representing jupiter). the track goes down to ground level, then to point q, the top of a sphere of radius r (representing neptune) and then back to the ground level. ignore air resistance, and assume friction between the cart and the track is negligible
To design a new solar system-themed roller coaster ride, engineers need to consider the forces acting on the cart as it moves along the track. The forces acting on the cart include gravity, centrifugal force, and normal force.
Gravity will act in the downward direction and will be equal to the mass of the cart multiplied by the acceleration due to gravity. The centrifugal force will act in the outward direction and will be equal to the mass of the cart multiplied by the square of the velocity divided by the radius of the track. The normal force will act in the upward direction and will be equal to the mass of the cart multiplied by the acceleration due to gravity minus the centrifugal force. The acceleration due to gravity can be calculated using the equation g = GM/r2, where G is the gravitational constant, M is the mass of the planet, and r is the radius of the planet. The velocity of the cart can be calculated using the equation v = √(2gh), where h is the height of the track. Once the forces acting on the cart have been determined, engineers can design the track to ensure that the forces are within acceptable limits.
Learn more about gravity here
https://brainly.com/question/4014727
#SPJ4
machine learning mastery with weka discover how to build predictive models in minutes without the code, without the math and without the confusion pdf
It also does not teach the process of building predictive machine learning models that can actually be used to make predictions.
What is prediction?
Prediction is an important reading strategy that encourages students to use details and clues in the text to predict what will happen next in the story. Encourages them to actively think ahead as they read to help them better understand the text. Anticipation is an ongoing process as the text unfolds as readers confirm or refute their assumptions. Anticipation can engage children in the story and help readers connect their prior knowledge to the text.
This ensures that the child can understand what they are reading while trying to make logical and reasonable guesses about what might happen next.
To learn more about predictions refer to:
brainly.com/question/25955478
#SPJ4
What is most nearly the force in member AE in the truss shown, where tension is positive and compression is negative?
The only two forces acting on a body in equilibrium must be co-linear, opposite in sign, and equal in magnitude.
In truss analysis, a negative member axial force denotes compression, whereas a positive member axial force denotes tension, for the member or joints at their ends. If a member has pins or supports at both ends and carries no weight in the middle, it is referred to as a two-force member. According to engineering definition, a truss is a structure made up of merely two force components that are placed in such a way that the assembly as a whole behaves as a single object. The only two forces acting on a body in equilibrium must be co-linear, opposite in sign, and equal in magnitude.
Learn more about Truss analysis here:
https://brainly.com/question/29582407
#SPJ4
if learning occurs as a result of exposure to any media, the learning is caused by the instructional method embedded in the medical presentation
Plagiarism is the practice of passing off someone else's words, concepts, or phrases as one's own.
Plagiarism is the practice of representing the ideas, words, or expressions of another author as one's own unique work. To put it another way, plagiarism is when someone directly quotes from another work, makes a little edit, and then claims authorship of the work. There are two types of paraphrasing: Correct paraphrasing is defined as paraphrasing that includes a citation. The term "inappropriate paraphrasing" refers to the act of stealing another person's ideas without giving them due credit. This is obvious copying. The material shown above is an example of paraphrasing plagiarism because the main idea was taken directly from the original source and then changed to appear original.
Learn more about Plagiarism here:
https://brainly.com/question/14500848
#SPJ4
if a furnace is using 1280 lbs./hr of oxygen, what is the correct balance equation and how much pentane will completely combustion?
The balance equation for pentane, C5H12's complete combustion is 5CO2 (g) + 6H2O = C5H12 (l) + 8 O2 (g) (g).
First, we should comprehend how hydrocarbons burn. A hydrocarbon, or molecule made up only of carbon and hydrogen atoms, is pentane, C5H12. When talking about the combustion of hydrocarbons, the two by products that are typically predicted are CO2 and 6H2O. Keeping in mind that "reaction with O2" refers to combustion, we may create the equation shown below: O2 (g) + C5H12 (l) + CO2 (g) + H2O (g), Therefore, we may determine the equation's balance by counting the number of atoms in each side of the equation. 5 C atoms, 12 H atoms, and 2 O atoms are on the right side. Left: one C atom, two H atoms, and three O atoms. By dividing CO2 by 5, we can begin to establish a balance: O2 (g) + C5H12 (l) = 5CO2 (g) + H2O (g).
Learn more about Combustion here:
https://brainly.com/question/29847993
#SPJ4
fill in the blank. constraints are ___ group of answer choices ... design properties of objects, which indicate to users the actions they can take. ... design decisions based on how affordable an object or system is. ... a term used to describe the overall aesthetic of a design. ... a limitation or restriction in a design, which prevents certain user actions.
An affordance in an object's design is how well the user loves the interface. An affordance is not an object's "attribute" as a result (like a physical object or a User Interface).
A user's ability-based potential with an object is referred to as its affordance. An affordance is not an object's "attribute" as a result (like a physical object or a User Interface). A user's ability-based potential with an object is referred to as its affordance. An affordance is not an object's "attribute" as a result (like a physical object or a User Interface). An affordance is instead defined by the interaction between the user and the thing: A door can be opened if you can get to the handle. The door cannot be opened if a young child cannot grasp the handle. An affordance is essentially a potential for an action in the interaction between a user and an object.
Learn more about An affordance here:
https://brainly.com/question/29032321
#SPJ4