a 1600-ft-long sag vertical curve (equal tangent) has a pvc at station 120 00 and elevation 1500 ft. the initial grade is -3.5% and the final grade is 6.5%. determine the elevation and stationing of the low point, pvi, and pvt

To accomplish this task, you can use the cp command with the -i option to prompt before overwriting existing files. The command would be:

cp -i /home/kcole/documents/*.txt /home/mruiz/personal/

This will copy all files with a .txt extension from the /home/kcole/documents directory to the /home/mruiz/personal directory and prompt before overwriting any existing files in the destination directory.

To learn more about existing click on the link below:

brainly.com/question/15102746

#SPJ11

The break-even threshold is reached when overall costs and total revenues are equal, leaving your small firm with no net benefit or loss.

Thus,  In other words, you've achieved the point in production where the revenue from a product equals the cost of manufacture.

This is a crucial calculation to include in your business plan for every new venture. Potential investors want to know when they may expect a return on their investment as well as the rate at which it will occur.

This is due to the fact that some businesses may take years before becoming profitable, frequently losing money in the initial months or years before achieving break-even. Therefore, break-even point is a crucial component of any business plan.

Thus, The break-even threshold is reached when overall costs and total revenues are equal, leaving your small firm with no net benefit or loss.

Learn more about Break even, refer to the link:

https://brainly.com/question/29063970

#SPJ1

The in-plane principal strains are ε_1 = 1110([tex]10^{-6}[/tex]) and ε_2 = 210([tex]10^{-6}[/tex]).

To establish the in-plane principal strains using the readings from a 45-degree strain rosette, we can use the following equations:

ε_x = (ε_a + ε_b)/2 + (ε_a - ε_b)/2 cos(2θ) + ε_c sin(2θ)

ε_y = (ε_a + ε_b)/2 - (ε_a - ε_b)/2 cos(2θ) - ε_c sin(2θ)

where ε_a, ε_b, and ε_c are the strain readings from the rosette for the three gauges at angles of 0, 90, and 45 degrees, respectively.

θ is the angle between the x-axis and the line passing through the gauge with ε_a.

Here, the strain readings are given as:

ε_a = 800([tex]10^{-6}[/tex])

ε_b = 520([tex]10^{-6}[/tex])

ε_c = 450([tex]10^{-6}[/tex])

Substituting these values into the above equations, we get:

ε_x = (800 + 520)/2 + (800 - 520)/2 cos(2(45°)) + 450 sin(2(45°))

= 660 + 140 cos(90°) + 450 sin(90°)

= 660 + 0 + 450

= 1110([tex]10^{-6}[/tex])

ε_y = (800 + 520)/2 - (800 - 520)/2 cos(2(45°)) - 450 sin(2(45°))

= 660 - 140 cos(90°) - 450 sin(90°)

= 660 - 0 - 450

= 210 ([tex]10^{-6}[/tex])

Therefore, the in-plane principal strains are ε_1 = 1110([tex]10^{-6}[/tex]) and ε_2 = 210([tex]10^{-6}[/tex])).

Learn more about in-plane principal strains at brainly.com/question/31387382

#SPJ4

False. Once a contractor has received notification that they have passed inspection, they are not relieved from the obligation to adhere to the documents. It is essential for the contractor to continue following the requirements, guidelines, and specifications outlined in the documents throughout the duration of the project.

This ensures that the work is carried out in accordance with the agreed-upon terms, and it helps maintain the quality and safety standards set by the project owner and any applicable regulatory bodies. Moreover, the contractor may still be subject to further inspections or audits, which will require them to demonstrate ongoing compliance with the documents. Additionally, maintaining adherence to the documents can help avoid disputes or potential legal issues arising from any non-compliance.

In summary, it is crucial for contractors to remain committed to the obligations stated in the documents, regardless of whether they have passed an inspection.

Learn more about contractor here:

https://brainly.com/question/14904683

#SPJ11

For a rescuer working in and around the rescue site, necessary equipment typically includes personal protective equipment (PPE), communication devices, specialized tools, and first aid supplies.

This ensures the rescuer while performing their duties at the site. PPE stands for Personal Protective Equipment. It refers to protective clothing, helmets, gloves, face shields, goggles, masks, and other equipment that is designed to protect the wearer from injury or the spread of disease. PPE is commonly used in a variety of settings, including industrial workplaces, healthcare facilities, laboratories, and construction sites. The specific type of PPE required will depend on the nature of the work being done and the potential hazards that workers may be exposed to.

Some examples of PPE include:

Respirators: These are used to protect against inhaling harmful dust, fumes, and chemicals.

Hard hats: These protect the head from impact and penetration hazards, such as falling objects or electrical hazards.

Gloves: These protect the hands from cuts, punctures, and chemical exposure.

Eye and face protection: This includes safety glasses, goggles, and face shields, which protect the eyes and face from flying debris, chemical splashes, and other hazards.

Protective clothing: This includes coveralls, aprons, and other clothing designed to protect the body from chemical exposure, flames, and other hazards.

Proper selection and use of PPE are important to ensure that it provides the intended protection. Employers are responsible for providing appropriate PPE to their employees and ensuring that it is used properly. Employees are responsible for wearing the PPE provided to them and follow any safety guidelines or protocols related to its use.

Learn more about PPE here:

https://brainly.com/question/28453648

#SPJ11

The angle between the horizontal axis and the radius that intersects point C represents the orientation angle of the outer normal of the plane with the largest principal stress, measured from the outer normal of the reference plane.

Unfortunately, I cannot see the Mohr's circle that you referred to in your question.

I can provide you with general information on how to determine the orientation angle of the outer normal of the plane with the largest principal stress, measured from the outer normal of the reference plane using Mohr's circle.

The orientation angle of the outer normal of the plane with the largest principal stress, measured from the outer normal of the reference plane, can be determined using the following steps:

Identify the point on the Mohr's circle that represents the state of stress at the point of interest.

Draw a horizontal line through this point to intersect the circle at points B and C.

Draw radii from the center of the circle to points B and C.

The angle is measured counterclockwise from the outer normal of the reference plane.

For similar questions on Orientation

https://brainly.com/question/30351525

#SPJ11

In order to get the full 8000 lbs support rating for a 8' t-spot shore made from 4x4's, the header and sole plate need to be at least 2x8.

This is because the header and sole plate are responsible for distributing the weight of the load across the entire length of the shore, and therefore need to be strong enough to handle the weight without buckling or bending. The header is the horizontal beam that sits atop the vertical 4x4's, while the sole plate is the horizontal beam that sits at the bottom of the 4x4's. By using a 2x8 header and sole plate, you can ensure that the weight of the load is evenly distributed and the 8' t-spot shore is able to support the full 8000 lbs rating.

It's important to note that these specifications may vary depending on the type of load you are supporting, as well as the height and width of the shore itself. Always consult with a qualified engineer or contractor to ensure that your shore is properly designed and built to handle the specific load you will be supporting.

Learn more about  header here: https://brainly.com/question/9979573

#SPJ11

If you go twice as fast, your stopping distance will increase by a factor of four. This is because stopping distance is directly proportional to the square of the speed. In other words, if you double your speed, your stopping distance will increase by a factor of four. This is a critical concept to understand for anyone who is operating a vehicle, whether it's a car, truck, or motorcycle.

Stopping distance refers to the total distance that a vehicle travels from the moment the driver applies the brakes until the vehicle comes to a complete stop. It is made up of two parts: the thinking distance and the braking distance. The thinking distance is the distance that the vehicle travels while the driver is reacting to the need to stop. The braking distance is the distance that the vehicle travels while the brakes are being applied.

In order to stay safe on the road, it's important to understand how speed affects stopping distance. If you are driving at a high speed, your stopping distance will be much greater than if you are driving at a lower speed. This means that it will take you longer to come to a complete stop, and you will need to be more cautious when driving in situations where you may need to stop suddenly. By keeping this in mind and driving at a safe and appropriate speed, you can help to prevent accidents and keep yourself and others safe on the road.

Learn more about distance here:

https://brainly.com/question/13034462

#SPJ11

As a question-answering bot, my most valuable way to see the sides and the rear involves utilizing comprehensive information sources and tools to provide accurate answers to users' inquiries. By accessing a wide range of reliable resources, I can analyze different aspects and viewpoints of a topic, enabling me to consider various angles and offer a well-rounded response.

Additionally, the integration of cutting-edge technology and artificial intelligence helps me understand complex queries, ensuring that users receive precise information to address their concerns effectively.

In this context, the "sides" represent different perspectives on a topic, while the "rear" signifies lesser-known or hidden aspects that are not readily apparent. By focusing on providing a comprehensive understanding of the subject matter, I can assist users in making informed decisions and gaining a deeper appreciation of various concepts. Overall, my ability to access and analyze vast amounts of data, combined with a commitment to delivering professional and friendly responses, makes me a valuable resource for users seeking reliable information and guidance.

Learn more about valuable here:

https://brainly.com/question/29382898

#SPJ11

To derive the magnitude of the transfer function for the given circuit in terms of[tex]C_{1}[/tex],[tex]C_{2}[/tex], and [tex]R_{1}[/tex], we need to start by identifying the type of circuit. However, since the specific circuit is not provided in your question, I cannot give a precise formula for the transfer function.

Generally, the transfer function H(s) is the ratio of the output Y(s) to the input X(s) in the Laplace domain, and its magnitude is given by |H(s)|. Depending on the circuit, the transfer function can be expressed in terms of C1, C2, and [tex]R_{1}[/tex]. Once you have the transfer function, you can create a Bode plot by plotting the magnitude response in decibels (dB) versus the frequency in a logarithmic scale from 100 Hz to 100 kHz. To do this, substitute s=jω (where j is the imaginary unit, and ω is the angular frequency) in the transfer function, calculate the magnitude for each frequency in the given range, and then convert it to decibels using the formula: 20 * log10(|H(jω)|). Since I do not have the specific circuit and numerical values, I cannot generate an exact Bode plot for you. However, once you have the transfer function, you can use any software or online tool to create the Bode plot, such as MATLAB or Python.

Learn more about logarithmic here: https://brainly.com/question/28346542

#SPJ11

The x-rays at the center of the beam are collectively known as the "central or primary beam" and are the most intense part of the x-ray beam.

In radiography, the x-ray beam is the primary source of radiation used to produce images of internal structures of the body. The central or primary beam refers to the x-rays that pass directly through the center of the beam and are the most intense part of the x-ray beam. These x-rays are important for creating high-quality images of the area of interest. However, it's important to limit exposure to the primary beam as much as possible to avoid unnecessary radiation exposure. Shielding and collimation techniques are used to help minimize radiation exposure to the patient and healthcare providers.

Learn more about x-ray beam here:

https://brainly.com/question/30247302

#SPJ11

The x-rays at the center of the beam are known collectively as central x-rays.

The x-rays at the center of the beam are referred to as the central or primary x-rays. When an x-ray beam is produced, it consists of a range of energies.

The central x-rays refer to the x-rays with the highest energy levels that are emitted from the focal spot of the x-ray tube. These x-rays travel in a straight line and have the greatest intensity at the center of the beam.

They play a crucial role in medical imaging and are responsible for creating the primary diagnostic information in X-ray radiography and computed tomography (CT) scans.

Read more about x-rays

brainly.com/question/24505239

#SPJ4

The type of loading that is designed to spread a load evenly across the surface is called "distributed loading."

In this type of loading, the load is spread out over a larger area, which helps to reduce the pressure on any one point of the surface. This is often achieved by using a material that is flexible or deformable, such as a foam or rubber mat, or by designing the surface itself to have a certain level of flexibility or give. Distributed loading is commonly used in a variety of applications, including flooring, where it helps to prevent damage to the surface and improve overall durability. It is also used in engineering and construction projects to distribute weight across large structures and reduce stress on individual components. Overall, distributed loading is an effective way to ensure that loads are spread evenly across a surface, helping to improve performance, durability, and safety.

learn more about surface here:

https://brainly.com/question/7690333

#SPJ11

A flow idealized as a throttling process through a device has D. h2 = h1 and p2<p1.

A throttling process is a measure in which a throttling valve is used to depressurize a high-pressure fluid into a low-pressure fluid. In this case, the enthalpy remains the same, in which case, h2 equals h1.

But there is a reduction in pressure in which case the second pressure will be less than the first pressure. So, P2 is less than P1. Of the options listed, option D fits best.

Learn more about the throttling process here:

https://brainly.com/question/12977208

#SPJ4

When the Si diodes are turning on at 0. 7V, it should be noted that the value of VB, V, I, and ID2 will be -0.7 volt, 0 volt, 0.86mA and 2ma respectively.

A two-terminal electrical element, called a diode, primarily allows current to flow in one direction. It has low resistance when conducting and strong resistance against the other direction.

It should be noted that a diode components may be applied for many uses, including rectification, voltage limitation, signal modulation, signal blending, switching, demodulation, oscillation, and regulating.

Based on the calculation, when the Si diodes are turning on at 0. 7V, it should be noted that the value of VB, V, I, and ID2 will be -0.7 volt, 0 volt, 0.86mA and 2ma respectively.

Learn more about diode on

https://brainly.com/question/24182272

#SPJ4

A network protocol is a set of rules that governs how communications are conducted across a network. In order for devices to communicate with each other on the network, they must all use the same network protocol.

The term that fits this definition is "network protocol." A network protocol is a set of rules and standards that dictate how devices communicate with each other over a network. This includes guidelines for data formatting, addressing, and transmission methods. In order for devices to communicate effectively on a network, they must all use the same network protocol. This ensures that data is transmitted correctly and that devices can understand and interpret the information being sent. Some examples of network protocols include TCP/IP, HTTP, and FTP. Without network protocols, communication on a network would be chaotic and unreliable.

learn more about network protocol here:

https://brainly.com/question/13327017

#SPJ11

When simulating the LED circuit in Tinkercad using a 1000 ohm resistor, the brightness of the LED will decrease compared to when using a 470 or 560 ohm resistor.

This is because the higher the resistance in the circuit, the less current will flow through the circuit. As a result, the LED will receive less power and therefore emit less light, resulting in a dimmer brightness. Conversely, when using a 220 ohm resistor in the circuit, the brightness of the LED will increase compared to when using a 470 or 560 ohm resistor. This is because the lower the resistance in the circuit, the more current will flow through the circuit. As a result, the LED will receive more power and emit more light, resulting in a brighter brightness.
To explain this change using KVL (Kirchhoff's Voltage Law), we can say that the voltage drop across the resistor increases as the resistance decreases, due to the same current flowing through the circuit. Therefore, less voltage is available to the LED, resulting in a dimmer brightness. Similarly, as the resistance increases, the voltage drop across the resistor decreases, resulting in more voltage available to the LED, resulting in a brighter brightness.

Learn more about resistance here: https://brainly.com/question/30799966

#SPJ11

To calculate the theoretical transfer function, you need to first analyze the circuit using circuit analysis techniques such as Kirchhoff's laws and Ohm's law.

Once you have obtained the expression for the transfer function, you can calculate the complex poles by setting the denominator of the transfer function equal to zero and solving for the roots. To generate a bode plot comparing the ideal transfer function to your measured data, you need to first read your measured data into Matlab and plot the magnitude and phase of the frequency response. Then, you can plot the theoretical transfer function on the same graph and compare the two plots. The deviations from theory at higher frequencies are due to the complex output impedance of the opamp. To briefly comment on the agreement of theory and experiment, you need to compare the two plots and identify any discrepancies. If the deviations are within an acceptable range, then the agreement is considered good. However, if the deviations are significant, then further investigation is required to determine the cause of the discrepancies.

Learn more about impedance here: https://brainly.com/question/30040649

#SPJ11

It's crucial to carefully assess the environment and potential loads when planning and constructing any type of building or infrastructure.

Loads resulting from the environment that the structure is located in refer to various natural forces and elements that can impact the stability and safety of the structure. These loads can include wind, seismic activity, snow and ice, temperature changes, moisture, and soil conditions. It's important for engineers and architects to consider these environmental factors when designing and constructing buildings and other structures to ensure that they can withstand these loads and remain structurally sound. The structure's location and surroundings play a significant role in determining the nature and intensity of these loads, and the content loaded into the structure can also have an impact.

learn more about  environment here:

https://brainly.com/question/11618163

#SPJ11

Sure! So a partition of a sample space is a way to divide the possible outcomes of an experiment into disjoint subsets that together cover the entire sample space. Here are four examples of partitions for the sample space of the measured resistances of two resistors:

1. Partition by total resistance: one subset for outcomes where the total resistance is less than some fixed value, and another subset for outcomes where the total resistance is greater than or equal to that value.

2. Partition by difference in resistance: one subset for outcomes where the difference in resistance between the two resistors is less than some fixed value, and another subset for outcomes where the difference in resistance is greater than or equal to that value.

3. Partition by which resistor has higher resistance: one subset for outcomes where the first resistor has higher resistance, one for outcomes where the second resistor has higher resistance, and one for outcomes where the resistances are equal.

4. Partition by range of resistance values: divide the range of possible resistance values into equal intervals (e.g. 0-10 ohms, 10-20 ohms, etc.), and create a subset for outcomes where both resistors fall within each interval.

Learn more about sample space: https://brainly.com/question/2117233

#SPJ11

To design a filter with infinite DC gain and a gain of one from 1Hz to 100Hz, while filtering any signals above 100Hz (1st order), we can use a high-pass filter with a cutoff frequency of 100Hz.

a) The Bode plot of this filter would show a flat line at infinity for frequencies less than 1Hz, a slope of 20dB/decade from 1Hz to 100Hz, and a sharp drop of 20dB/decade for frequencies above 100Hz.
b) The s-plane would show a single pole at -100rad/s.
c) The transfer function of this filter can be written as: H(s) = (s+100)/s
d) The differential equation for this filter can be written as: [tex]y''(t) + 100y'(t) + y(t) = 100x'(t) + x(t)[/tex]
e) The unforced transient response for this filter can be written as: y(t) = [tex][c1e^(-50t)cos(99.5t) + c2e^(-50t)sin(99.5t)][/tex]
f) The frequency response for this filter is given by: H(jw) = (jw + 100) / jw.

For more questions on DC

https://brainly.com/question/29123104

#SPJ11

The transition between the corrosion protection for the bond and free stressing lengths is a crucial aspect of structural design, as it ensures the long-term durability and integrity of the structure. This transition involves carefully designing and implementing measures to protect the bond and free stressing lengths from corrosion, which can weaken the structural elements and ultimately compromise the safety and stability of the entire structure.

In order to ensure a seamless transition between these two protection measures, several factors must be considered during the design process. First, the materials used in the bond and free stressing lengths should be compatible, as they will be exposed to similar environmental conditions and potential sources of corrosion. The use of high-quality materials with proven corrosion resistance is essential to minimize the risk of corrosion-related issues.

Next, proper detailing and reinforcement placement should be incorporated into the design to maintain adequate cover and ensure the bond and free stressing lengths are well-protected from potential corrosion. This may involve using a combination of passive and active corrosion protection systems, such as the application of protective coatings, the use of galvanic anodes, or the implementation of cathodic protection.

Additionally, the construction process should be carefully planned and executed to maintain the integrity of the corrosion protection measures during installation. This includes the proper handling and storage of materials, strict adherence to construction standards, and thorough quality control measures to verify the effectiveness of the implemented protection systems.

By taking these factors into account and designing the transition between the corrosion protection for the bond and free stressing lengths with careful consideration, engineers can help ensure the long-term durability and performance of the structure.

Learn more about transition here:

https://brainly.com/question/17998935

#SPJ11

When calculating box conductor fill, all of the following shall be counted except for the grounding conductor.

This means that you should include current-carrying conductors, devices such as switches and receptacles, and cable clamps when determining the fill capacity of a box. The grounding conductor, however, is not counted in this calculation. When calculating box conductor fill, all of the following shall be counted except for:

1. Conductors that are shorter than 6 inches
2. Grounding conductors
3. Equipment bonding jumpers
4. Conductors for electric signs and outline lighting
5. Conductors for luminaires
6. Conductors for fixtures
7. Conductors for appliances

To learn more about conductor visit;

https://brainly.com/question/18084972

#SPJ11

Douglas Fir is a popular wood species for construction due to its strength and durability.

However, like all wood, it has different properties along the grain direction. The compressive strength of Douglas Fir varies depending on the orientation of the wood grain. Cross-grain components, where the load is perpendicular to the grain, will start to crush at approximately 1,000 to 1,500 psi. Parallel grain components, where the load is along the grain, will start to fail at approximately 6,000 to 10,000 psi. It is important to consider these differences in strength when designing structures using Douglas Fir, and to ensure that the appropriate safety factors are applied to prevent failures and ensure the longevity of the structure.

To learn more about construction click on the link below:

brainly.com/question/31487212

#SPJ11

To execute the delete statements in SQL, do the following:

DELETE from Horsetable WHERE ID = 5

AND Breed = Holsteiner

AND Birth date < March 13, 2013;

In the Structured Query language, the delete statement can be used to remove the rows and columns that we no longer want in a database.

To execute this delete statement with multiple conditions, the WHERE function will be used to specify the particular rows to be deleted provided that some conditions are met.

Learn more about SQL here:

https://brainly.com/question/25694408

#SPJ4

The  dialect L = L(aaaa*b*): The dialect L comprises of all strings that begin with four continuous a's, taken after by zero or more b's. The taking after could be a depiction of a Turing machine that acknowledges this language below.

The Turing machine begins within the beginning state q0. In state q0, the machine filters the input tape seeking out for the primary a. When it finds an a, it composes a extraordinary image "#" on the tape, moves the head to the proper, and moves to state q1.

Therefore, In state q1, the machine uses an input symbol and checks on the off chance that it is an a or a b. If it is an a, it composes the image "#" on the tape, moves the head to the proper, and remains in state q1. If it could be a b, the machine moves to state q2.

Learn more about Turing machine   from

https://brainly.com/question/27851066

#SPJ4

The concrete cover refers to the distance between the edge of the concrete and the embedded elements, such as the wedge cavity area of the anchor. This distance is crucial in ensuring the structural integrity, durability, and protection of the reinforcement within the concrete.

The minimum required distance for the concrete cover varies depending on factors such as the type of anchor, environmental conditions, and load requirements. Typically, the concrete cover should be large enough to provide protection against corrosion and damage to the embedded anchor, while also ensuring the effective transfer of forces between the anchor and the surrounding concrete.

For wedge anchors, the minimum concrete cover is usually specified by the manufacturer and is determined based on testing and evaluation of the anchor's performance in various concrete conditions. The concrete cover requirements may also be influenced by building codes and engineering design specifications.

In general, a minimum concrete cover of 1.5 to 2 times the anchor diameter is recommended for wedge anchors to ensure proper functioning and long-term durability. However, it is essential to consult the manufacturer's guidelines and relevant building codes to determine the appropriate concrete cover for the specific application and anchor type.

Learn more about concrete here:

https://brainly.com/question/28903866

#SPJ11

A prestress member is a structural element that has been intentionally preloaded with a force to enhance its strength and durability. The preloading force is typically applied to the member before it is subjected to any external loading conditions, such as during construction or fabrication.

The highest level of prestress force is achieved during the initial stage of the member's life when the member is first preloaded. This is because the full amount of prestress force is applied to the member, and there is no external loading to counteract this force. On the other hand, the concrete compressive strength is at its lowest during the initial stage of the member's life. This is because the concrete has not yet fully cured and hardened, and therefore, its compressive strength is not at its peak. As time passes and the concrete cures, its compressive strength gradually increases. In summary, the prestress force is at its highest during the initial stage of the prestress member's life, while the concrete compressive strength is at its lowest. As time passes and the concrete cures, its compressive strength increases, while the prestress force may decrease due to relaxation or other factors.

Learn more about preloading force here-

https://brainly.com/question/30185722

#SPJ11

Technician A and technician B both are correct in their statements. Large amounts of Electromagnetic Interference can negatively impact the function of a coil and spark plug, while poor insulation in spark plug cables can contribute to the generation of EMI. Proper maintenance of ignition system components and good-quality insulation are essential for minimizing EMI-related issues in vehicles.

Technician A is correct in saying that large amounts of Electromagnetic Interference (EMI) can collapse the magnetic field in a coil, causing a spark plug to fire prematurely or improperly. This occurs when external electromagnetic disturbances interfere with the normal operation of electrical circuits, particularly those that involve coil and ignition systems.
Technician B is also correct in stating that poor spark plug cable insulation may cause EMI. Damaged or deteriorated insulation can allow electromagnetic disturbances to be emitted from the high-voltage spark plug cables.

For more questions on vehicles

https://brainly.com/question/30094730

#SPJ11

To determine the length of a raker shore in inches, two things are required to be known: the height of the load and the angle of the raker. The height of the load is the vertical distance from the ground to the top of the load, while the angle of the raker is the angle between the raker and the horizontal ground.

The hypotenuse rule of thumb calculation is a quick and easy way to estimate the length of the raker shore. It states that the length of the raker shore is approximately equal to 1.5 times the height of the load divided by the sine of the angle of the raker. For example, if the height of the load is 10 feet and the angle of the raker is 45 degrees, the length of the raker shore would be approximately 15.5 feet (1.5 x 10 / sin 45). However, it is important to note that this rule of thumb is only an estimate and should not be relied upon for precise calculations.

learn more about raker here:

https://brainly.com/question/30138454

#SPJ11