when the filament breaks in one lamp in a series circuit, other lamps in the circuit normally _________.
Answer:
when the filament breaks in one lamp in a series circuit, other lamps in the circuit normally stop working.
Explanation:
Cooling water available at 10°C is used to condense steam at 30°C in the condenser of a power plant at a rate of 0.60 kg/s by circulating the cooling water through a bank of 7-m-long 1.2-cm-internal-diameter thin copper tubes. Water enters the tubes at a mean velocity of 4 m/s and leaves at a temperature of 24°C. The tubes are nearly isothermal at 30°C. Determine the average heat transfer coefficient between the water, the tubes, and the number of tubes needed to achieve the indicated heat transfer rate in the condenser.
Answer:
Dang this looks hard
Explanation:
A person’s ability to use understand and relate to technology is known as :
A: Technology literacy
B: computer literacy
C: Technology knowledge
D: computer comprehension
Pick one out of those please
Answer:
A: Technology literacy
I took a computer class in the 8th grade.
Explanation:
hope this helps. . . <3
good luck! uωu
if we model the vibrating system as a mass on a spring, what is the mass necessary to achieve the desired resonant frequency when the tip is not interacting with the surface?
Answer:
2.5 micrograms
Explanation:
The frequency of a vibrating body reduces with increasing mass, but increases with increasing tension.
What is the relation of resonant frequency with mass?For a spring-mass system, the relationship between frequency and mass can be expressed as follows: as mass increases, frequency decreases; as mass decreases, frequency increases.
The frequency in this case is f, and the mass is m. The relationship between mass and frequency is therefore inverse.
Precession frequency drops when mass is doubled, since angular momentum also doubles at this point. As the radius grows, the angular momentum increases and the precession frequency decreases.
Mass and stiffness are two well-known factors that affect an object's resonance frequency.
While stiffness limits low-frequency transmission because less elastic, or stiff, materials vibrate at higher frequencies, mass limits high-frequency transmission because larger objects vibrate at lower frequencies.
Therefore, The resonant frequency should rise as mass decreases.
Learn more about frequency here:
https://brainly.com/question/13191113
#SPJ5
Which type of valve is required on the suction side of the fire pump, allowing the pipe to be open to the full diameter of water flow
Answer:
Gate Valve
Explanation:
Technician A says that comparing the front vehicle height sensors to the rear sensors allows the ECM to determine body roll created by cornering force. Technician B says that vehicle height sensors are only located on the rear. Which technician is correct
Answer:
its b
Explanation:
Technician A says a typical Manifold Absolute Pressure (MAP) sensor can be connected directly to the intake manifold or connected through a vacuum hose. Technician B says most modern MAP sensors do not use a flexible silicon chip within a chamber anymore. Who is correct
Answer:
the correct answer is: technician A
Explanation:
this answer is taken directly from the book
One method of determining engine load is through the use of a manifold absolute pressure (MAP) sensor. The MAP sensor can be either directly bolted to the intake manifold or connected through a vacuum hose.
Most modern MAP sensors use a type of flexible silicon chip within a sealed chamber; the chip changes resistance when manifold pressure flexes the chip.
Which of the following is a type of Interior door?
Answer:
There is no answers given
Explanation:
How to handle or hold sharp edged tools in welding
Answer: I got you bestie :)
When walking with a sharp tool, the tool should be carried with the blade down and away from the body. When climbing with a sharp tool, tool belts, or buckets with hand lines should be used so workers can have both hands to grip the ladder.
Answer:
sharp egdes should be held far from the body just in case you fall you won't really get cut by it
Explanation:
thanks for the points
PDA is an abbreviation for professional diagnostic assistant
True or false
Answer:
False
Explanation:
It means Public Display of Affection
Some benefits of science
Answer:
Scientific knowledge allows us to develop new technologies, solve practical problems, and make informed decisions — both individually and collectively. Because its products are so useful, the process of science is intertwined with those applications: New scientific knowledge may lead to new applications.
Explanation:
On diesel engines, data from ________ sensors are commonly used to adjust exhaust gas recirculation (EGR) rates.
Answer:
Air mass sensors is the right answer i think
Explanation:
State three means of operating a power tool
Answer:
A power tool is a tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools. The most common types of power tools use electric motors. Internal combustion engines and compressed air are also commonly used. Other power sources include steam engines, direct burning of fuels and propellants, such as in powder-actuated tools, or even natural power sources such as wind or moving water. Tools directly driven by animal power are not generally considered power tools.
Power tools are used in industry, in construction, in the garden, for housework tasks such as cooking, cleaning, and around the house for purposes of driving (fasteners), drilling, cutting, shaping, sanding, grinding, routing, polishing, painting, heating and more.
Power tools are classified as either stationary or portable, where portable means hand-held. Portable power tools have obvious advantages in mobility. Stationary power tools, however, often have advantages in speed and precision. A typical table saw, for instance, not only cuts faster than a regular hand saw, but the cuts are smoother, straighter, and more square than what is normally achievable with a hand-held power saw. Some stationary power tools can produce objects that cannot be made in any other way. Lathes, for example, produce truly round objects.
Stationary power tools for metalworking are usually called machine tools. The term machine tool is not usually applied to stationary power tools for woodworking, although such usage is occasionally heard, and in some cases, such as drill presses and bench grinders, exactly the same tool is used for both woodworking and metalworking.
Explanation:
If we have to become a pilot what class should we choose
.
Science,
economics,
or commerce
Answer:
Class Not Necessary For Army
Explanation:
Just a normal degree is enough
Answer:
Degree Is Enough
Explanation:
Bcz of There is Class
Plzz help me plzzzz plzz
Answer:
A. Air powered
Explanation:
Pneumatic tools are compressed air driven power tools powered by an air compressor.
My cramps hurt sm and I’m so emotional
Answer:
Okay? I can try to help you.
Go to sleep.Cry in pain.I hope this helped at all.
Answer:
Man up you women. Eat some travis scuout burjer
if a load has a resistance of 5 ohms, how much current will it draw from a 120-volt power supply?
how to clean corroded battery terminals in electronics
is there water on mars
Answer:
nope, it is phsically impossible for water to be on mars
Explanation:
Always report damage tools to the
Answer:
Tool enginear??????
Explanation:
sorry for wrong spellin
Answer:
Explanation:
How do people put virus
Answer:
Explanation:
Don’t know
when you are performing an advanced filter, in which argument box do you enter the range for the dataset?
Explain the purpose of wrench plzzz
Answer:
Wrenches are made in various shapes and sizes and are used for gripping, fastening, turning, tightening and loosening things like pipes, pipe fittings, nuts and bolts. There are basically two major kinds of wrenches: Pipe wrenches used in plumbing for gripping round (cylindrical) things.
Which type of weld is made by welding around the perimeter of a
hole?
Joints between two overlapping components are made by depositing a fillet weld around the perimeter of a hole in one component so that it can be attached to the surface of another component exposed through the hole.
Some aluminum casting alloys can be heat-treated after casting for added strength. Group of answer choices False True
What is energy security, and why is it an important issue for many countries?
Answer:
What is energy security? Energy security is the association between national security and the availability or natural resources for energy consumption.
why is it an important issue for many countries? To ensure that their economics function without interruption and that their people have access to adequate, reliable and affordable supplies of modern and clean energy
The form of energy delivered to an electrical generating turbine in a geothermal facility is in the form of ________.
Geothermal energy is a product of the heat of Earth's molten interior. The form of energy delivered to an electrical generating turbine in a geothermal facility is in the form of hot water or steam.
Geothermal energy is gotten so as to generate electricity. This is done when water is injected deep underground and it then comes back as steam or hot water.This is then converted to steam so as to drive a turbine on an electric power generator. The plants makes use of steam to produce electricity.
There are three main types of energy for electricity generation. They are fossil fuels which is made up of coal, natural gas, and petroleum, and then nuclear energy, and renewable energy sources.
Learn more from
https://brainly.com/question/24161565
What is true about a point and shoot camera?
They always have lenses u can take on and off
They are often smaller than SLR cameras
They are used by professionals more often that SLR cameras
All of the above
Answer:
What is true about a point and shoot camera?
They are often smaller than SLR camerasAnswer:
They are often smaller than SLR cameras
Explanation:
All of the following are benefits of consuming complex carbohydrates, EXCEPT:
complez carbs have fiber and starch
Answer:
spikes blood sugar quickly is something it doesn't help with
Explanation:
complex-are starches and dietary fibers. They include whole grains such as wheat, barley, bulgar, rye, millet, oats, pasta, rice and legumes. Carbohydrates are our main source of energy. About 50%-60% of your plate at each meal should be composed of carbohydrates. Besides supplying you with long-lasting energy, carbohydrates also supply other nutrients such as vitamins, minerals and protein.
what factors need to be considered when building housing on a waterway
Answer:
Flooding
Explanation:
.
When building housing on a waterway one must always consider the factor of Flooding and its repercussions.
What is a Flood?A flood occurs when there is an excessive amount of water and it covers normally dry areas. The word can also refer to the tide's influx when used in the sense of "flowing water." Floods are a topic of research in the hydrology field and are very important to the fields of agriculture, civil engineering, and public health.
Floods have serious societal repercussions for both communities and people. As most people are well aware, flooding has a number of direct effects, including the loss of life, destruction of property, loss of crops and livestock, and worsening of health due to waterborne infections.
Stream gauges that are put in bodies of water close to inhabited areas are used to measure floods. The National Weather Service receives all data collected by them before it is sent to the United States Geological Survey (USGS), which erected and operates them (NWS)
To read more about Floods, refer to - https://brainly.com/question/28725721
#SPJ2