If the speed of the magnet is doubled, the induced voltage is twice as great
Faraday's law of induction states that whenever relative motion exists between a coil and magnetic field, a voltage will induce in the circuit and this voltage is proportional to the rate of change of the flux. The expression for the motional emf is as follows:
ε=Blv
Here, ε is the motional emf, B is the magnetic field, l is the length of the conductor, and v is the velocity at which the magnetic field changes.
The induced voltage by the moving magnet is directly proportional to the speed of the magnet. Therefore, an increase in the speed of the magnet will increase the induced voltage.
If the speed of the magnet is doubled, the induced voltage is twice as great
Find out more at: https://brainly.com/question/13369951
In three to five sentences, identify the acid, base, conjugate acid, and conjugate base. Use patterns in the periodic table to explain why the substances you identified acted as the acid and the base in this reaction.
A conjugate acid is formed from the base by accepting a proton from the acid .
A conjugate base is obtained from the Brownstead - Lowry acid when it looses a proton while the conjugate acid is obtained from the Brownstead - Lowry base when it accepts a proton. In the Brownstead - Lowry sense, acid base reaction involves the loss or gain of a proton.
Consider the hypothetical reaction; AH + :B ⇄ BH + :A. The specie BH is the conjugate acid while the specie :B is the Brownstead - Lowry base . The specie :A is the conjugate base while the specie AH is the Brownstead - Lowry acid.
Learn more about conjugate acid: https://brainly.com/question/10468518
identify the origins of breakdown when using a spectrum analyzer
Four regions of the electromagnetic spectrum that astronomers use when observing objects in the space are the following enumerated answers.
1. First is Ultraviolet
2. Next is Infrared
3. Then the radio
4. Lastly the Visible lights.
These are the answers to the problem.
When a 1 is on the input of an inverter, what is the output?
Answer:
When the input to an inverter is high (1) the output is low (0); and when the input is low, the output is high.
8th grade science !
can someone help me with trying to understand this question for my homework especially how to understand the graph and use that for my evidence and help me give an idea of how should I write the evidence and reasoning?
Answer:
for reasoning you could put -> the line is at the top at the left handed sided of the chart (also the beginning) slopes down towards the very bottom right handed side of the chart, symbolising less force as distance goes.
4. If a charged body is negatively charged, it has excess of _______
Answer:
Electrons
Explanation:
Electrons are negatively charged sub-atomic particles, therefore when a body's negatively charged, it means that there's more electrons than protons.
True or False. Abraham and Sarah were in agreement regarding God's command to sacrifice Isaac.
Answer:
Explanation:
Not in Genesis. The proposed sacrifice of Isaac was all Abraham's doing. Sarah was not present and could not, therefore offer any input. It might have been covered in other Jewish writings, but it is not recorded in Genesis.
Since the book most widely used by Everyone is the Bible, I would answer false.
An airplane accelerates from rest down a runway at 9.50 m/s2 for 29.3 seconds when it
takes off. What is the distance traveled while taking off?
Answer:
Explanation:
s = ½at²
s = ½(9.50)(29.3²) = 4,077.8275
s = 4080 m
when rounded to the three significant digits of the question numerals.
Who actually asked Abraham to sacrifice his son?
Answer:
Allah asked Abraham(Ibrahim)
A gold fish weighing 13g has a speed of 8.8m/s. What is its Kinetic energy
Answer:
0.47 J
Explanation:
2. Define Lightning conductor. How does it work?
In Building, there are a host of protective devices that are installed to protect lives and properties, one of them is the Lightning Conductor that a metal rod mounted on a structure and intended to protect the structure from a lightning strike. It works on the principle of induction
Principle of Operation of Lightning ConductorThe lightning conductor works on the principle of induction:
When a charged cloud passes by the building hosting the Lightning conductor, it gets a charge opposite to that of the cloud through the process of induction. They are Typically made from copper material.Most Lightening conductors are made from copper materials.
Learn about Lightning Conductor:
https://brainly.com/question/2824044
14. Earthworms are crucial for forming soil. As they search for food by digging tunnels,
they expose rocks and minerals to the effects of weathering. Over time, this process
creates new soil. Worms are not the only living things that help to create soil. Plants
also play a part in the weathering process. As the roots of plants grow and seek out
water and nutrients, they help to break large rock fragments into smaller ones. Have
you ever seen a plant growing in a sidewalk? As the plants grows, its roots spread into
tiny cracks in the sidewalk. These roots apply pressure to the cracks, and, over time,
the cracks become larger, ice wedging can occur more readily. As the cracks expand,
more water can flow into them. When the water freezes, it expands and presses against
the walls of the cracks, which makes the cracks larger. Over time, the weathering
caused by water, plants, and worms help to form soil. QUESTION: Ice wedging, as
described in the passage, is an example of which of the following?
A mechanical weathering
B. Oxidation
C. chemical weathering
D. Hydrolysis
Ice wedging, as described in the passage, is an example of mechanical
weathering.
Mechanical weathering is also known as physical weathering and it
involves the breaking of rock into smaller particles without causing changes
in the chemical properties.Mechanical weathering is usually carried through
physical processes such as freezing and thawing etc.
In this scenario, we were told that water freezes, expands and presses
against the walls of the crack thereby breaking into smaller parts which is a
physical process hence mechanical weathering being present.
Read more about Mechanical weathering on https://brainly.com/question/458304
Identify the types of motion a) The movement of a snail on the ground b) The strings of the guitar c) The whirling of stone tied with a thread
Answer:
1. friction, gravity,
Explanation:
Suppose you want to make the demonstration more dramatic by attracting as much hair as possible with the balloon. Which of the following is the best choice to accomplish your goal? A. Decrease the electric force by holding the balloon closer to the hair. B. Increase the electric force by rubbing the balloon for a longer period of time. C. Decrease the electric force by using a larger balloon. D. Increase the electric force by holding the balloon farther away from the hair.
Answer:
B. Increase the electric force by rubbing the balloon for a longer period of time.
Explanation:
An Astronaut lands on an Earthlike planet and drops a small lead ball with a mass from the top of her spaceship. The point of release is 25 m above the surface of the planet and the ball takes 5 s to reach the ground. The astronaut's mass is 80 kg. Astronaut weight on the planet is
PLEASE NO LINKS, REAL ANSWERS DON'T WASTE TIME.
First we have to find out the gravity on that planet. We use Newton second equation of motion. It is given as,
s = ut +(gt^2)/2
Distance s = 25m
Time t = 5 s
Velocity u = 0
By putting these values,
25 = 1/2.g.(5)²
g = 2
So the gravity on that planet is 2. Lets find out the weight of the astronaut.
Mass of the astronaut on earth m = 80 kg
Weight of astronaut on earth W = mg = (80)(9.8) = 784 N
Weight of astronaut on earth like planet = (80)(2) = 160 N
x = 160N
Please answer the question in the picture, worth 25 points
I will report any links or false answers immediately
Answer:
Option C, increases and decreases
Explanation:
When an object making noise approaches you, the wave frequency increases leading to a higher pitch. Conversely, when it moves away from you or retreats, the wave frequency decreases leading to a lower pitch. This can be observed in ambulance sirens.
The diagram below shows a child pulling a 50.-kg friend on a 20 kg sled by applying a 300. newton force on the sled rope at an angle of 40 degrees with the horizontal. The sled moves at constant velocity as the person pulls with the 300 N force.
The vertical component of the applied force on the sled is 192.84 N.
The given parameters:
Mass of the friend, M = 50 kgMass of the sled, m = 20 kgApplied force, F = 300 NInclination of the force, θ = 40 ⁰The vertical component of the 300 N force is calculated as follows;
[tex]F_y= F \times sin(\theta)\\\\F_y = 300 \times sin(40)\\\\F_y = 192.84 \ N[/tex]
Thus, the vertical component of the applied force on the sled is 192.84 N.
Your question is not complete, the missing part of the question is below:
The vertical component of the 300 N force is approximately?
Learn more about vertical component of forces here: https://brainly.com/question/7181504
An ammeter has azero offset error This fault will affect
Answer:
An ammeter has a zero offset error. This fault will affect. neither the precision nor the accuracy of the readings. only the precision of the readings.
The accuracy of the present measurement will be impacted by an ammeter's zero offset inaccuracy, but the precision of the measurement will not change.
What is resistance?Resistance is the obstruction of electrons in an electrically conducting material.
voltage = current ×resistance
How accurate measurement or reading is may be determined by its accuracy. The measurements will be off because of zero inaccuracy.
Thus, The precision of the measurement would not alter if an ammeter made a mistake with its zero offsets, but the accuracy of the current measurement would be decreased.
To learn more about resistance, refer to the link;
brainly.com/question/14547003
#SPJ2
if the force acting on a body of mass 40 k.g is doubled by how much will the acceleration change
Answer:
Explanation:
Ignoring friction, the acceleration will double
F = ma
2F = m(2a)
Which type of muscle cell can have multiple nuclei
Answer:
Skeletal Muscle cells
Skeletal muscle cells are long, cylindrical, and striated. They are multi-nucleated meaning that they have more than one nucleus. This is because they are formed from the fusion of embryonic myoblasts.
Answer:
skeletal muscle cells can have multiple nuclei
Explanation:
This is because they are formed from the fusion of embryonic myoblasts.
The work done by an electric force in moving a charge from point A to point B is 2.70 × 10‒3 J. The electric potential difference between the two points is VA ‒ VB = 50.0 V. What is the charge?
The charge moved by this electric force is [tex]5.4 \times 10^{-5} \; Coulombs[/tex].
Given the following data:
Work done = [tex]2.70 \times 10^{-3}\;Joules[/tex]Potential difference = 50.0 VoltsTo determine the charge:
Mathematically, the work done by an electric force in moving a charge from one point to another is given by the formula:
[tex]W = PQ[/tex]
Where:
W is the work done.P is the electric potential difference.Q is the charge.Making Q the subject of formula, we have:
[tex]Q =\frac{W}{P}[/tex]
Substituting the given parameters into the formula, we have;
[tex]Q =\frac{2.70 \times 10^{-3}}{50}\\\\Q =5.4 \times 10^{-5} \; Coulombs[/tex]
Read more on charge here: https://brainly.com/question/14327016
The gradual increase in activity over time is called
Answer:Progression is the way in which an individual should increase the load. It is a gradual increase either in frequency, intensity, or time or a combination of all three components.
Explanation:
The ability to do work and cause change is called
Answer:
I am pretty sure it is called energy.
Select the correct answer. Chloe is playing the flute some distance away from a crowd. If the atmospheric temperature is 15°C, what is the speed of the sound traveling from the flute? A. 340 meters/second B. 330 meters/second C. 320 meters/second D. 310 meters/second E. 300 meters/second
Answer:
A. 340 meters/second
I think this is the right answer.
.
A distance-time graph indicates that an object travels 2 m in 2 s and then travels another 80 m during the next 40 s.
What is the average speed of the object?
Answer:
Explanation:distance-time =speed
a,V =s/t
V=2m/2s
V=1m/s
b,v=s/t
V=80m/40s
V= 2m/s
The average speed is 2m/s
Using the figure shown, if I₃= 1.17 A, then (I₁ , I₂) A is:
a- (3.17 , 2.00)
b- (1.33 , 0.17)
c- (1.67 , 0.50)
d- (1.27 , 0.10)
The value of the current in each arm of the circuit is given by Kirchhoff's
Rules.
The correct option for (I₁, I₂) is; b-. [tex]\underline{(1.33, \ 0.17)}[/tex]Reasons:
By Kirchhoff's junction rule, we have that the sum of current at a junction is given as follows;
[tex]\displaystyle \mathbf{ \sum \limits_{k = 1}^ n I_K} = 0[/tex]Which by the direction of the currents in the given circuit diagram, we have;
I₁ - (I₃ + I₂) = 0Therefore;
I₁ = I₃ + I₂
According to Kirchhoff's loop rule theory, we have;
[tex]\displaystyle \mathbf{\sum \limits_{k = 1}^ n V_K} = 0[/tex]In the loop having the 2 Volts emf., we have;
-I₃·R₁ + 2 + I₂·R₂ = 0
I₃ = 1.17 A
R₁ = 2 Ω
R₂ = 2 Ω
Which gives;
-1.17 × 2 + 2 + I₂×2 = 0
I₂ × 2 = 2.34 - 2 = 0.34
I₂ = 0.34 ÷ 2 = 0.17
I₂ = 0.17 A
From the loop having the 7 Volts emf. we have;
7 - 0.17×2 - I₁ × 4 - I₁ × 1 = 0
Which gives;
7 - 0.34 - 5·I₁ = 0
5·I₁ = 7 - 0.34 = 6.66
I₁ = 6.66 ÷ 5 = 1.332
Therefore;
[tex]\underline{\mathbf{(I_1, \, I_2)} = (1.33, \, 0.17)}[/tex]Learn more about electric circuits here:
https://brainly.com/question/2608877
Transverse waves move particles back and forth along the same direction in which the waves travel.
True false question.
True
False
Answer:
False, I am pretty sure.
Explanation:
Transverse waves are always characterized by particle motion being perpendicular to wave motion. ... As a sound wave moves from the lips of a speaker to the ear of a listener, particles of air vibrate back and forth in the same direction and the opposite direction of energy transport.
A wire that is 1.0 m long with a mass of 90 g is under a tension of 710 N. When a transverse wave travels on the wire, its wavelength is 0.10 m. What is the frequency of this wave?
Answer:
890 HzI hope you liked my answer. Thank You!
Which is the answer
Answer:
no idea thanks you veryuch
18. Why is the sun included in this model of the water cycle?
A. The water cycle takes place in the atmosphere and and since the sun can be
seen through the atmosphere it make the model more detailed
B. The sun is the driving force that provides the energy that keeps the water cycle
going
C. The water cycle takes place in the hydrosphere and since the sun makes it
possible for us to see everything it is included in the picture.
D. The sun is part of condensation and run-off
Answer:
b
Explanation:
1st grade common sense
25.Figure 22.22 shows a plot
of potential versus position
along the x-axis. Make a plot
of the x-component of the
electric field for this situation.
The relationship between the potential and the electric field allows to find the results for the value of the electric field as a function of the distance is:
In the attachment we see the graph of the electric field as a function of distance.
Electric potential is defined by the change in potential energy of a test charge between two points, between the value of the test charge.
dV = - E . ds
E = [tex]- \frac{dV}{ds} \ \hat s[/tex]
Where the bold letters indicate vectors, V is the potential difference, E the electric field and s the path.
Let's apply this expression for each section of the given graph:
1) section from x₀ = 0 to x_f = 2 m, the potential is V₀ = 2 V is constant.
The derivative of a constant is zero.
E = 0
2) Section between x₀ = 2 and x_f = 4 m, the potential varies linearly from V₀ = 2 v to V_f = -2 V.
We look for the equation of the line.
V-V₀ = m (x- x₀)
We carry out the derivative.
E = - m i ^
The slope (m) is:
[tex]m= \frac{V_f - V_o}{x_f- x_o}[/tex]
Let's calculate.
[tex]m= \frac{-2 -2}{4-2} = \ -2 \ V/m[/tex]
Let's substitute.
E = [tex]2 \hat i \ V/m[/tex]
3) From x₀ = 4 to x_f = 4.5 m, the potential varies from V₀ = -2 to V_f = 0.
We look for the equation of the line and we derive.
E = - m i ^
Let's substitute.
[tex]m = \frac{0-(-2)}{4.5-4} = \ 4 V/m[/tex]
E = - 4 [tex]\hat i[/tex] V / m
4) From x₀ = 4.5 m to x_f = 6m. The potential is constant and the derivative of a constant is zero.
E = 0
5) From x₀ = 6m to x_f = 8 m, the potential changes linearly from v₀ = 0 to V_f = 1 V
We look for the equation of the line and we derive.
E = - m i ^
[tex]m = \frac{1-0}{8-6} = \ 0.5 \ V/m[/tex]
E = - 0.5 [tex]\hat i[/tex] V/m
6) From x₀ = 8m to x_f = 9m, the potential changes linearly from V₀ = 1 V to V_f = -1.
We look for the equation of the line and we derive.
E = - m i ^
[tex]m = \frac{-1-1}{9-8} = \ -2 \ V/m[/tex]
Let's substitute.
E = 2 [tex]\hat i[/tex] V/m
7) From x₀ = 9m to x_f = 10 m, the potential changes linearly from V₀ = -1 V to V_f = -2 V
We look for the equation of the line and we derive.
E = - m i ^
[tex]m = \frac{-2+1}{10-9} = \ -1 \ V/m[/tex]
Let's substitute.
E = 1 [tex]\hat i[/tex] V/m
In the attachment we can see these Electric fields as a function of distance.
In conclusion, the relationship between the potential and the electric field we can find the results for the value of the electric field as a function of the distance is:
In the attachment we see the graph of the electric field as a function of distance.
Learn more about the electric field here: brainly.com/question/14306881