Do you think the plan for the skyscraper in California is appropriate based on its location? Why or why not? Your answer should include at least three complete sentences.

Answer:

Yes! I can Answer that!

Explanation:

C) Block the inlet of the valve.

A blocked drain on a pressure-reducing valve can prevent the valve from functioning correctly by blocking the drain line that is used to relieve excess pressure from the valve. As a result, the inlet of the valve can become blocked, causing the valve to malfunction and preventing it from reducing pressure. It is important to keep the drain line clear to ensure that the pressure-reducing valve works properly.

Answer:

Here is the example how to do it

Explanation:

We can use the formula for the modulus of elasticity to solve for the diameter of the steel rod:

modulus of elasticity = (stress / strain) = (force / area) / (change in length / original length)

Solving for the area of the steel rod, we get:

area = (force * original length) / (modulus of elasticity * change in length)

Substituting the given values, we get:

area = (8,000 lb * 420 in) / (30,000,000 psi * 0.266 in) = 0.105 in^2

The area of a circle is given by the formula:

area = pi * (diameter/2)^2

Substituting the value we just calculated, we get:

0.105 in^2 = pi * (diameter/2)^2

Solving for the diameter, we get:

diameter/2 = sqrt(0.105 in^2 / pi) = 0.182 in

diameter = 2 * 0.182 in = 0.364 in

Therefore, the diameter of the steel rod is 0.36 in (to two decimal places).

I believe the answer is A, explore the test, learn the content, follow test day rules. Hope this helps! Please give me brainliest :)

Note that if the  vanelli family is building a house and wants to save anywhere they can the choice that would be most expensive electric system for them to operate is a Heat Pump. (Option a)

A heat pump is a device tha tuses electricity to generate heat so that during winter and very cold period, the house is kept warm.

This is notably one of th most expensive devices to maintain in a home.

Hence it will be very expensive for the Vanelli familyto build a house that has many heat pumps. They can opt for solar powered heat pumpts instead.

Learn more about heat pumps:
https://brainly.com/question/13198025
#SPJ1

The Vanelli family is building a house and wants to save money anywhere they can. Which of the

following choices would be the most expensive electric system for them to operate?

A. Heat pump

B. Baseboard

C. Radiant ceiling

D. Program clock

The balance that I believe should be maintained in deciding how land and its resources should be used is adopting sustainable practices.

The concept of sustainability calls for the practice of utilizing resources in a fashion that not just fulfills the requirements of presently, yet also preserves enough to support generations hereafter. This method of operation helps to guarantee that resources are being tapped rationally and applied responsibily all while preserving nature's equilibrium and environmental variety.

Particular ecosystems such as those found in wetlands, coral reefs, and woodlands hold significance in keeping up the overall health of the planet, and should take precedence in conservation efforts.

Learn more about land on

https://brainly.com/question/21537812

#SPJ1

3. Gears are wheels with teeth that slot together. When one gear is turned the other one turns as well. If the gears are of different sizes, they can be used to increase the power of a turning force. The smaller wheel turns more quickly but with less force, while the bigger one turns more slowly with more force.

4. 4.10 gears are going to accelerate faster and decelerate faster on the lift. However, the trade-off is greater fuel consumption per mile driven and higher engine speed per given road speed. In basic terms, the 4.10 gears will feel quicker and 3.73 will feel faster.

Answer:

Here is your Answer Bellow!

Explanation:

Wiring a doorbell button switch in the normally-open (NO) state is preferred because it is safer and more reliable than wiring it in the normally-closed (NC) state.

In a doorbell circuit, when the doorbell button is pressed, it completes the circuit and allows current to flow to the doorbell, causing it to ring. In the NC configuration, the button switch is always closed, and current flows through the circuit even when the button is not pressed. This can cause several problems, such as short circuits, overheating, and premature wear on the doorbell and other components in the circuit.

On the other hand, in the NO configuration, the button switch is open when it is not pressed, and no current flows through the circuit. When the button is pressed, it closes the circuit and allows current to flow, causing the doorbell to ring. This configuration is safer because it minimizes the risk of short circuits, overheating, and premature wear on the components in the circuit.

In addition to being safer, the NO configuration is also more reliable because it is less prone to false triggers. In the NC configuration, the button switch can be triggered by vibration, accidental contact, or other factors, causing the doorbell to ring unnecessarily. In the NO configuration, however, the button switch must be deliberately pressed to trigger the doorbell, making it less likely to ring accidentally.

Overall, wiring a doorbell button switch in the normally-open state is the preferred configuration for safety, reliability, and durability.

Wiring a doorbell button switch in the normally-open (NO) state is preferred because it is safer and more reliable than wiring it in the normally-closed (NC) state.

In a doorbell circuit, when the doorbell button is pressed, it completes the circuit and allows current to flow to the doorbell, causing it to ring. In the NC configuration, the button switch is always closed, and current flows through the circuit even when the button is not pressed. This can cause several problems, such as short circuits, overheating, and premature wear on the doorbell and other components in the circuit.

On the other hand, in the NO configuration, the button switch is open when it is not pressed, and no current flows through the circuit.

Learn more about configuration on:

https://brainly.com/question/13410673

#SPJ1

Answer:

The diameter of the rod can be determined using the following formula:

Explanation:

d = sqrt(4L / (pi * E * delta))

where:

d = diameter of the rod

L = length of the rod = 35 ft

E = modulus of elasticity of the steel = 30,000,000 psi

delta = elongation of the rod = 0.266 in

First, we need to convert the length of the rod and elongation to inches to maintain consistency with the units of E:

L = 35 ft * 12 in/ft = 420 in

delta = 0.266 in

Substituting the given values into the formula:

d = sqrt(4 * 420 / (pi * 30,000,000 * 0.266))

d = 0.615 in (rounded to 0.01)

Therefore, the diameter of the steel rod is 0.62 inches (rounded to 0.01).

Answer:

taken at the same time to ensure accurate results.

Explanation:

Answer:

For the "Lab: Kinetic Energy" on edge for Physical Science B, the answer is

Graph B

Explanation:

I went looking for the answer on brainly, but I couldn't find a reliable answer, so I guessed and got it right so... yay! Here ya go, hope it helps ;p

Answer:

Yes! I can help with.

Explanation:

To compare materials H and K, we need to determine the modulus of elasticity for each material. The modulus of elasticity is a measure of a material's stiffness, specifically the amount of stress required to produce a given amount of strain.

We can use the formula:

stress = force / area

strain = change in length / original length

modulus of elasticity = stress / strain

Let's start by calculating the stress on each wire:

For wire 1:

stress = force / area = (225 lb) / ((pi/4) * (3/8 in)^2) = 7,655 psi

For wire 2:

stress = force / area = (225 lb) / ((pi/4) * (3/16 in)^2) = 30,620 psi

Next, we can calculate the strain on each wire:

For wire 1:

strain = change in length / original length = 0.10 in / 480 in = 0.000208

For wire 2:

strain = change in length / original length = 0.25 in / 480 in = 0.000521

Finally, we can use the formula to calculate the modulus of elasticity for each material:

For material H:

modulus of elasticity = stress / strain = 7,655 psi / 0.000208 = 36,824,038 psi

For material K:

modulus of elasticity = stress / strain = 30,620 psi / 0.000521 = 58,745,334 psi

Therefore, material K has the greater modulus of elasticity and is the stiffer material.