Answer:
Slinky is the correct answer.
10 time 20 minus 5 and yeah that’s all i need
Answer:
[tex]10 \times 20 - 5 \\ \\ = 200 - 5 \\ = 195[/tex]
All satellite eventually lose their orbital energy and plummet to earth because of______.
Answer:
gravity
Explanation:
Even when satellites are thousands of miles away, Earth's gravity still tugs on them. Gravity—combined with the satellite's momentum from its launch into space—cause the satellite to go into orbit above Earth, instead of falling back down to the ground.
The ratio between the force of friction and the normal force is called:
A.the drag
B.rolling friction
C.the coefficient of friction
D.the starting friction
Answer:
C.the coefficient of friction
Explanation:
Hope this helps. can i have brainliest thanks!
An experiment is conducted such that an applied force is exerted on a 5kg object as it travels across a horizontal surface in which frictional forces are NOT considered to be negligible. A graph of the net force exerted on the object as a function of the object’s distance traveled is shown. How could a student use the graph to determine the net work done on the object?
If an experiment is conducted such that an applied force is exerted on an object, a student could use the graph to determine the net work done on the object.
The graph of the net force exerted on the object as a function of the object’s distance traveled is attached below.
A student could use the graph to determine the net work done on the object by Calculating the area bound by the line of best fit and the horizontal axis from 0m to 5mFor more information on work done, visit
https://brainly.com/subject/physics
Answer:
D. There is not enough information that is known or can be obtained from the graph to determine the net work done on the object.
Explanation:
it’s the answer For Ap classroom
"PLS HELP ME WITH THIS QUESTION!" Two factors that affect climate patterns on Earth are the tilt of Earth on its axis and the topography of Earth. Describe how these two factors affect the climate patterns of Earth.
Answer:
The tilt of the Earth causes some places to be hit more by the sun's rays, while the topography affects wind travel.
Explanation:
Because of the way the Earth is tilted on its axis, some parts receive more heat due to being hit more directly by the sun's rays. This is the reason why the North pole is very cold since it doesn't get directly hit by the sun's rays. As for the topography, the way the wind travels is affected by mountains, and the temperature of winds are affected by the places the wind originated from. Also, high altitude places such as mountain summits are colder, while low altitude places are warmer. So, when an area is under direct sunlight, it causes warm climate, and when an area receives warm air because of its topography, it causes further heat.
please help me !! i’ll mark brainliest if you’re right!
Please help me answer this! ANSWER IN SCENTENCE FORMAT!!! :
Two factors that affect climate patterns on Earth are the tilt of Earth on its axis and the topography of Earth. Describe how these two factors affect the climate patterns of Earth.
Answer:
If you are saying How much does the tilt of the Earth affect the climate
This varies between a tilt of 22.1 and 24.5 degrees over a period of about 41,000 years. This trend not only affects the average temperature of the earth, but also how prominent the seasons are. Procession is a wobble in the earth's axis.
? Any idea on this I’m getting some mixed up
Answer:
1. electrochemical reaction
2. combustion
3. photosynthesis
4. respiration
Explanation:
Student 1 lifts a box with a force of 500 N and sets it on a tabletop 1. 2 m high. Student 2 pushes an identical box up a 5 m ramp from the floor to the top of the same table. Which student did the MOST work?.
The student 2 did the MOST work because he pushed the box to a greater height.
The given parameters:
Force applied by Student 1 = 500 NHeight of table for student 1 = 1.2 mHeight of ramp for student 2 = 5 mThe work done by student 1 is calculated as follows;
Work = P.E = mgh
P.E = 1.2mg
The work done by the student 2 is calculated as;
P.E = 5mg
where;
m is the mass of the boxThus, we can conclude that the student 2 did the MOST work.
Learn more about work done here: https://brainly.com/question/8119756
What does the risk of biological harm from radiation depend on?
Answer:
The effects of radiation depend on the type, energy, and location of the radiation source, and the length of exposure.
The gravitational potential energy of the ball changes as it bounces. Where is the ball located when its gravitational potential energy is greatest? Where is the ball when its gravitational potential energy has the least value?
When the planet is closest to the Sun, speed v and kinetic energy are the highest, and gravitational potential energy is the lowest. When the planet moves farther away, the speed and kinetic energy decrease, and the gravitational potential energy increases.
A car has a kinetic energy of 4.33x10^5 J when traveling a speed of 25 m/s. What is the mass ?
can you fit all the planets between earth and moon
Answer: No, planets of our solar system, with or without Pluto, cannot fit within the mean lunar distance. An additional 3,500 km is needed to squeeze in Neptune
45. What is the wovelength of a 30. Hertz periodic
wave moving ol 60. meters per second?
a. 0.50m
c. m
b 20m
d 1800 m
The wavelength is 2m.
Hence, Option c) 2m is the correct answer
Given that;
Frequency; [tex]f = 30Hz[/tex]
Speed; [tex]v = 60m/s[/tex]
Wavelength; [tex]\lambda =\ ?[/tex]
using the expression for the relations between wavelength, frequency and speed of wave:
[tex]\lambda = \frac{v}{f}[/tex]
Where [tex]\lambda[/tex] is wavelength, f is frequency and v is speed.
We substitute our given values into the equation
[tex]\lambda = \frac{60m/s}{30Hz}\\\\\lambda = \frac{60m/s}{30s^{-1}}\\\\\lambda = 2m[/tex]
The wavelength is 2m.
Hence, Option c) 2m is the correct answer.
To learn more about wavelength, click here: https://brainly.com/question/1347107
The frequency of the moving wave is 30 Hz and if it is moving at the speed of 60 m/s then the wavelength will be equal to 2 m.
What is Wavelength?The distance between two identical locations (adjacent crests) in successive cycles is known as the wavelength, and it is used to describe waveform signals that are transmitted over wires or into space. Typically, in wireless systems, this length is specified in meters (m), centimeters (cm), or millimeters (mm).
The wavelength is more frequently described in nanometers (nm), which are units of 10⁻⁹ m, or angstroms, which are units of 10⁻¹⁰ m, for infrared (IR), visible light (UV), and gamma radiation.
As per the provided given data in the question,
Frequency, f = 30 Hz
Speed, v = 60 m/s
Then, the wavelength of the moving wave will be,
λ = v/f
= 60/30
λ = 2 meters.
Therefore, the wavelength will be 2 meters.
To know more about Wavelength:
https://brainly.com/question/13533093
#SPJ2
I couldn't find one .
Start from the top and go 7 down then go to the right 9 times and there you should fine the letter "one"
do forces that act a distance come in pairs?
Answer:
Forces come in pairs.
Explanation:
Distances are between two points. The distance from A to B is equal but opposite the distance from B to A.
A water balloon is hovering directly above the line join points ANB which are 4.6 km apart if the angles of elevation to the balloon from point a to B or 28.8° and 52.2 respectively find the altitude of the balloon
Answer:
Drawing the triangle:
H / x = tan 52.2 = 1.29
H / (4.6 - x) = tan 28.8 = .550
H = 1.29 x
H = .55 * 4.6 - .55 x
1.84 x = 2.53 combining equations
x = 1.38
4.6 - 1.38 = 3.22
Total base of triangle = 1.38 + 3.22 = 4.6
H / x = tan 52,2 = 1.29
H = 1.29 * 1.38 = 1.78 height of triangle
Check:
1.78 / 3.22 = tan 28.9
This agrees with the given value of 28.8
A geothermal plant has been built in a location. Which of these is the most likely benefit of the geothermal plant in this location?
A. Decrease in geothermal fuels consumption
B. Improvement to hot springs and geysers
C. Long-term cost savings for energy users
D. Increase in emission of greenhouse gases
Answer:
C
Explanation:
A and B are not true and D is a disadvantage
Answer:
C. Long-term cost savings for energy users.
Explanation:
C is correct because the first option is a drawback that is unlikely. B is a good answer but not the best. It's a likely benefit, but C is a more likely benefit. D is a drawback. C is correct. I also got this right on my quiz.
Hope this helps!
Read the excerpt from The Building of Manhattan.
A temporary, small narrow-gauge track system was installed on each floor as it was needed. This enabled the material to be moved from the truck at ground level onto dump carts, raised by elevator to the designated floor, wheeled onto the track, and moved quickly to the exact spot needed. Turntables built into the track allowed the carts to be shifted about in any direction.
Which question can be answered only if an illustration accompanies the text?
What did turntables built into the track allow?
How were dump carts raised to designated floors?
When was a track system installed on a floor?
What does a turntable built into a track loo
Answer: this would be D.) What does a turntable built into a track look like
Explanation:
Which statement most completely describes a Lewis electron dot diagram? A.
a representation of the electrons that form bonds in a molecule
B.
a representation of the total number of electrons in an element, compound, or ion
C.
a representation of the total number and arrangement of electrons in an element, compound, or ion
D.
a representation of the arrangement of valence electrons in an element, compound, or ion
Answer:
D.
Explanation:
it is indeed a representation of how the valence electrons in an element,coumpound, or ion are arranged.
to ensure you i was just quized on this and D is the correct anwser
A representation of the arrangement of valence electrons in an element, compound, or ion - statement most completely describes a Lewis electron dot diagram. Hence, option (D) is correct.
What is Lewis electron dot diagram?If the compound's molecular formula is known, electron dot structures or Lewis dot formulas can be drawn.
It describes the type of bond and the placement of the atoms within the molecule that are joined together. In honor of American chemist Gilbert Newton Lewis, molecules are depicted as having a Lewis electron dot structure or simply a Lewis structure.
Lewis dot structures, also known as electron dot structures, are schematics that show the interatomic chemical bonds in a molecule. Additionally, they show how many lone pairs there are overall in each of the atoms that make up the molecule. Common names for Lewis dot structures include electron dot structures and Lewis structures. Lewis described an acid as an electron pair acceptor, while a base is an electron pair giver.
Learn more about Lewis electron dot diagram here:
https://brainly.com/question/19093827
#SPJ2
Describe the direction in which each object will accelerate. If the object won't accelerate, write "no acceleration." Explain what might be happening to each object in terms of its overall motion.
A race car makes one lap around a track of radius 180 m in 90.0 s. What is the centripetal acceleration in m/s2?
a
0.5
12.6
Ob
OC
Od
.87
2.
2
Answer:
0.9m/s^2 (yours is 0.87, so choose that)
Explanation:
formula for centripetal acceleration:
v^2/r
to find v, we know that f=1/90s, and r=180m.
v=(2pir)/T
v=(2pi(180))/90
v=12.6m/s
now plug into a=v^2/r
a=(12.6)^2/180
a=0.9m/s^2
1. Sandra buys a $4 000 television and pays $2 000 deposit. The rest is payable in 8 equal monthly payments. If the flat rate of interest charged is 7% p.a. what is the total amount paid for the item?
Answer:
$2140
Explanation:$2000 missing plus 7 percent of 2000 is 140 so 2000+140=2140. Each month she would pay $268 approx.
advantages of writing very large and very small numbers in the terms of power of ten
Answer:
Large numbers might create fuse, be confusing and if you miss even one of the zeros it is a very big deal in a situation when you are making a spaceship. Hope this answers your questions :) Merry Christmas. Have fun.
Explanation:
2
Explanation:
for saving space in large numbers
and small numbers for multiplying easily
soda is an example of which of these?
liquid–liquid solution
gas–liquid solution
solid–liquid solution
solid solution
Samantha's teacher asks her to describe motion in one dimension. This type of motion is always
A motion in one dimension is a type of motion that is always along a straight line and has a constant acceleration.
Motion refers to a change in the location (position) of an object or physical body with respect to a reference point, especially due to the action of an external force.
In Science, the motion of an object or physical body is described in terms of the following parameters:
SpeedForceAccelerationDistanceTimeFurthermore, there are three (3) forms of motion based on dimension and these include:
1. Motion in one dimension
2. Motion in two dimension
3. Motion in three dimension
A motion in one dimension (one-dimensional motion) is also referred to as rectilinear or linear motion. Also, it is always along a straight line in any direction and characterized by constant acceleration.
Read more on motion here: https://brainly.com/question/17675825
find u + (3v - w)
u =-4i-8j
v= -11i -3j
w=5i+7j
Answer:
gunrun
Explanation:
if a tent is touched with a finger on inner surface , when it is raining , it allows the rain water to leak through. give a reason for this observation
Explanation:
When water vapor in the air comes into contact with something cool, like the ceiling of a tent, its molecules slow down and get closer together. When that happens, the gaseous water vapor turns back into liquid water droplets. That's condensation!
which statement is not correct about force.
A, force causes deformation
B, force xauses accleration
C, if there is no force, there is no motion
D, force emerges due to interaction.
Answer:
c
Explanation:
without force motion won't take place
Which does not apply to unbalanced forces?
Net force = 0
Have direction
Net force does not = 0
Changes an object's motion
Answer:
Net force = 0
Explanation:
Whenever there is an unbalanced force, it shows that the net force doesn’t = 0 because if net force = 0, then everything force is balanced by another force. If there is an unbalanced force, acceleration will occur in the direction the net force is towards.