(b) The application of user centred design can lead to innovative products such as the umbrella shown in Figure 9.
Explain the concept of user centred design and how it may have influenced the design of the umbrella shown in Figure 9. (6 marks)
Answers
Answer:
the concept of user centred design is the idea of putting your clients best needs in mind. you need to be empathic and understanding of how to make their life easier. by doing research you can do this. for example the design in figure 9 shows an umbrella with a canopy. the canopy can deflect rain and still have the easy design of an umbrella. this makes it not only easier to use but functional.
Explanation:
i wrote this myself so copy it or just rewrite it, it doesnt matter
Related Questions
A technician notes that an operating air-conditioning system has ice formed on the suction line at the condensing unit. The technician can reasonably assume that:
Answers
The technician can reasonably assume that evaporator coil is frozen over.
An air-conditioning system makes a place cooler by absorbing heat from the
surrounding. This is usually done with the aid of the evaporator coil.
In situations whereby there are ice particles formed on the suction line at the
condensing unit then it means the air conditioning system is faulty and must
be turned off to prevent damage to other parts.
Read more about Air conditioning system here https://brainly.com/question/24920322
True of false an understaffed store can cause loss of inventory
Answers
Answer:
probably true, if it's understaffed people are more likely to steal and the overworked workers that still remain are likely to make more mistakes
True.
It's important to keep a balance of store labor with incoming consumer traffic. Understaffing affects the impact of profitability.
true or false tensile forces are smaller in arch bridges
Answers
Answer:
True
Explanation:
The tensile forces are small in most arches and usually negligible.
determine the moments of inertia of the quartercircular area about the x- and y- axes, and find the polar radius of gyration about point o.
Answers
How do robots demonstrate the modern, technological Japan? *
Answers
Robots demonstrate modern, technological Japan because it serves as brought economical success to Japan since it help them to build products faster and efficiently.
According to the question, we are to discuss how the robot help japan in terms of technology and modernization.As a result of this we can see that Japan is moving forward in technology with development of robot because it makes them to build more products.
Therefore, Robot has brought economical success to Japan
Learn more about robot at:
https://brainly.com/question/10387419
in what flight condition is torque effect the greatest in a single-engine airplane?
Answers
Answer:
Low airspeed, high power, high angle of attack
¿Qué es una restricción FACTIBLE?
El tema es sobre Programación Lineal.
Por favor no se roben los puntos, necesito una respuesta.
NO WIKIPEDIA.
Answers
Answer: A feasible solution for a linear program is a solution that satisfies all the constraints of the linear programming problem. There could be many solutions that satisfy all the restrictions. Any point in the feasible region is a feasible solution for the LPP. A feasible solution for a linear program is a solution that satisfies all the constraints.
Explanation: Hope this helps: ^
what element is the primary constituent of ferrous alloys?
Answers
Answer: Ferrous alloys or metals are metals that consist mostly of iron (Fe). Steel is an iron-based alloy containing typically less than 1% carbon, where iron frequently contains 2% or more carbon.
MANUFACTURING QUESTION PLEASE HELP
Answers
Answer:
"He then pours the metal into a mold and allows it to solidify."
2) What kinds of food can you eat in space?
Answers
Answer:
fruits, nuts, peanut butter, chicken, beef, seafood, candy, brownies now if we talking about drinks ,coffee, tea, orange juice, fruit punches and lemonade
Explanation:somehow this all are delicious
WHICH LUBRICATION SYSTEM RECEIVES OIL FROM THE OIL SUPPLY TANK, PRESSURIZES THE OIL, SENDS THE OIL THROUGH THE FILTER AND DELIVERS THE OIL TO THE BEARINGS
Answers
Answer:
The following is the answer.
Explanation:
PRESSURE SYSTEM.
Many amateur video games suffer from what kind of layout?
A. an overly neutral layout
B. an overly simplistic layout
C. an over-crowded layout
D. a boring layout
Answers
Answer:
D a boring layout I think but you welcome
the basic purpose of adjusting the fuel/air mixture at altitude is to
Answers
Answer:
The basic purpose of adjusting the fuel/air mixture at altitude is to. ... increase the amount of fuel in the mixture to compensate for the decrease in pressure and density of the air
1. What are hand tools ? *
1 point
2. Give one example and one use of the following handtools I. Measuring tool II. Cutting Tool III. Striking tool *
6 points
3. Name the hand tool used to drive nails *
1 point
4. Name the hand tool used to cut plastic and metal pipes *
1 point
5. Which hand tool is used to clamp your work piece to the work table ? *
1 point
6. What are portable power tools? *
1 point
7. Name the power tools used to carryout the following operations I. Boring holes II. Cutting curves III. Sanding *
3 points
8. List three examples of stationary machines *
3 points
Answers
Answer:
Microsoft Word - Hand tools SON
John has an exhaust leak in his Acura Integra GS-R, What steps would he take to fix the leak in time for his inspection?
Answers
Answer:
Explanation:
Fist you need to identify where the leak is coming from. You can do this by either listening for the leak or spraying soapy water on the exhaust to look for air bubbles coming out of the exhaust. Depending on the spot of the leak there are many ways you can fix this leak.
1. Exhaust clamp
2. Exhaust putty
3. Exhaust tape
4. New exhaust
Exhaust clamp is best used for holes on straight pipes.
Putty is best used on welds or small holes like on exhaust manifolds or welds connecting various pieces like catalytic converters, mufflers, or resonators.
Tape will work best on straight pipes with holes.
New exhaust is for when the thig is beyond repair, like rust.
Now good luck because working on exhausts is a pain.
if a population has no predadors and plenty of available resources, how might that population change
Answers
Answer:
B (exponential growth )
Explanation: wish u the best bby <33
why are you directed not to touch the holder or discharge tube whule the power to the supply to the gas tube is on?
Answers
Every profession has its rules and regulations. The reason why we are directed not to touch the holder or discharge tube while the power to the supply to the gas tube is on because;
The discharge tube can create about 5000 V of voltage when connected to power.The gas discharge tubes is often very hot when used with the power supplies and one should not to touch them until they are cooled down.
We have been taught to stay far was from a high voltage area or system and also we should not dare to touch it.
There are different reasons why we should about these high voltage system or are; The reason is that;
Because high voltages often reduce the impedance of our skin, thereby making electricity to flow through our bodies.Learn more about Voltage from
https://brainly.com/question/1176850
Help!!
So I think that someone is tracking my truck with an apple airtag but I don't know for sure. The only apple product I have is an iPad and I don't know how to check if an airtag is near by!!
Answers
Explanation:
I mean honestly it depends like how old is it? is it one of the newer generations because a majority of apple products have airtags but their is also the lost my iPhone app so they can track where ever their iPad or iPhone is.
What is the voltage across the load, RL, in
this voltage divider network?
10.25 V
4.55 V
5.71 V
11.50 V
Answers
Answer:
(c) 5.71 V
Explanation:
The circuit can be redrawn to a Thevenin equivalent that is 6V through a 5-ohm resistor into a 100-ohm load. Then the voltage at the load is ...
(6 V)(100/(100 +5) ≈ 5.71 V
Please help for our stem project :(
Explain how Ratio and proportion affect the strength of the Bridge.
STEM Project
Answers
Answer:
Do you have some a picture
Which is NOT an example of labour intensive industry?
Healthcare practitioner
steel production industry
local farmers
small cakery
Answers
Answer:
small cakery
Explanation:
it only makes food it does not cut logs, wood etc.
Answer:
small cakery
Explanation:
cakery or bakery don't require labour services almostThere hardly one or two person works so it can't be called labour intensive industryAll of the following are examples of capital intensive industries EXCEPT: *
1 point
Soft drink production
oil extraction
manufacturing
hospitality
Answers
Answer:
hospital
Explanation:
Soft drink production is a capital intensive industry as it's depends upon the economy and trade.Oil extraction is a national industry and it also involves the intention of trade.Manufacturing is similar to soft drink production and has intense of trade.Hospital doesn't has the intention of trade so it's the answercan someone help showing the steps please
Answers
Answer:
a) 20 Ω
b) 1 A
c) 10 V on each
d) 1/3 A through each
e) 10 W in R1, 3 1/3 W in the others
f) 20 W
Explanation:
The three 30 Ω resistors are in parallel with each other, so will have an equivalent resistance of (30 Ω)/3 = 10 Ω.
(a) The total circuit resistance is 10 Ω + 10 Ω = 20 Ω.
__
(b) All of the current supplied by the battery passes through R1. The current supplied by the battery is ...
I = V/R = (20 v)/(20 Ω) = 1 A
__
(c) The voltage drop on R1 is (1 A)(10 Ω) = 10 v. Subtracting that from the battery voltage gives the voltage drop on the other resistors:
20 v -10 v = 10 v . . . . drop on R2, R3, R4
__
(d) The current through resistors R2, R3, R4 is ...
I = V/R = (10 v)/(30 Ω) = 1/3 A
__
(e) Power can be computed several ways. Here, it may be easiest to use ...
P = VI
For R1, that is P1 = (10 v)(1 A) = 10 W
For R2-R4, that is P2-P4 = (10 v)(1/3 A) = 10/3 W = 3 1/3 W
__
(f) The total power dissipated is the total power supplied:
P = VI = (20 v)(1 A) = 20 W
Adding up the power in the resistors, we get ...
P = 10 W + 3·(10/3 W) = 20 W
A factory hires a consultant to recommend ways to improve its productivity. The consultant notices that the production floor is strewn with tools and machines that are not continually in use. Which of the 5S philosophies should the consultant recommend to the management to establish better productivity?
A.
set in place
B.
sort
C.
standardize
D.
shine
E.
sustain
Answers
Answer:
B
Explanation:
Keep only what is used. Remove all unnecessary items. Red tag these items for review.
Select the correct answer. which process involves creating a product by heating metals and changing their shape through the application of mechanical force?
A. finishing
B. forming
C. assembling
D. casting
would it be forming? or casting? I'm so lost
Answers
Answer:
I would say that it is forming.
Explanation:
Give brainliest if u can. :S
At an open or uncontrolled intersection, yield if _____.
Need Help
Answers
a wire is not strong enough to pick up a washer or much of anything. what is a way to strengthen the magnetic field?
Answers
Answer:
making it straight and making it exercising every time
1. Write an equation that shows the equivalency between meters and Gigameters.
Answers
10^9 m = 1 Gm
what are some benfits of getting involved with 4h
Answers
Answer:
the kids can get smarter and make the country where they live better
4h can help with making the next generation better, and better if we help them
Oil refining is an example of:
Construction Production
Extractive Production
Domestic Production
Traditional Production
Answers
Extractive industry, can be defined as a processes that involve different activities that lead to the extraction of raw materials from the earth (such as oil, metals, mineral and aggregates), processing and utilization by consumers.