The correct answer is C) mechanically actuated motors. A full brake-by-wire system replaces the hydraulic portion of the brake system with sensors, wires, and an electronic control unit, but not mechanically actuated motors.
Instead, the brake system is actuated through electrical means, such as electric motors, digital computers, or fiber optic cables.
Mechanically actuated motors are motors that use mechanical force, such as a spring, to drive the motor. These motors are used in a variety of applications, from toys to industrial machinery, and can be found in a wide range of sizes and shapes. Mechanically actuated motors have several advantages over other types of motors, such as low cost, low maintenance, and the ability to produce high torque at low speeds.
Learn more about electrical :
https://brainly.com/question/24786034
#SPJ4
A circuit consists of five elements. How much power is dissipated or delivered by element 5 if element 1 is delivering P1 = 730 mW of power, element 2 is absorbing P2 = 762 mW of power, element 3 is absorbing P3 = 170 mW of power, and element 4 is delivering P4 = 820 mW of power.
The power dissipated or delivered by element 5 can be calculated by subtracting the power absorbed by elements 1, 2, and 3 from the power delivered by element 4.
Therefore, the power dissipated or delivered by element 5 is P5 = P4 - (P1 + P2 + P3) = 820 mW - (730 mW + 762 mW + 170 mW) = -32 mW. This means that element 5 is absorbing 32 mW of power.The power dissipated or delivered by element 5 can be calculated by subtracting the power absorbed by elements 1, 2, and 3 from the power delivered by element 4. Therefore, the power absorb delivered by element 5 is P5 = P4 - (P1 + P2 + P3) = 820 mW - (730 mW + 762 mW + 170 mW) = -32 mW. This means that element 5 is absorbing 32 mW of power. This is because the total power absorbed by elements 1, 2, and 3 is greater than the power delivered by element 4. Therefore, element 5 must absorb the difference in order to maintain the balance of power in the circuit.
Learn more about power here
https://brainly.com/question/30150415
#SPJ4
Need help to answer.
ASAP.
Air at a temperature of 150C passes through a heat exchanger at a velocity of 30 m/s where its temperature is raised to 8000C. It then enters a turbine with the same velocity of 30 m/s and expands until the temperature falls to 6500C. On leaving the turbine, the air is taken at a velocity of 60 m/s to a nozzle where it expands until the temperature falls to 5000C. If the air flow rate is 2 kg/s, calculate the following.
(i) Rate of heat transfer to the air in the heat exchanger,
(ii) Power output from the turbine assuming no heat loss, and
(iii) Velocity at exit from the nozzle, assuming no heat loss.
Take the enthalpy of air as h =cpt, where cp is the specific heat equal to 1. 005kJ/kg K and t is the temperature.
The power output from turbine assuming no heat loss and the velocity at exit from nozzle where Enthalphy h CpT i.e Cp specific heat = 1.005KJ/KgK.
What is meant by velocity?
Velocity is the direction speed of an item in motion as a measure of the rate at which its location is changing as seen from a certain point of view and as measured by a specific unit of time.A particle or object's movement with respect to time is expressed vectorially as velocity.As an alternative, the velocity magnitude can be expressed in centimetres per second (cm/s).Simply said, velocity is the rate of motion of an object in a specific direction. Using an automobile driving north on a highway as an example, or a rocket after it has launched, as an example of speed.The rate of flow of heat transfer to air exchanger i.e
[tex]w(h1+v^{2} 1/2+Z1g)+Q_{1-2} =w(h2+v2^{2} /2+Z1g)W_{1-2}[/tex]
[tex]Wh_{1} +Q_{1-2} =Wh_{2}[/tex]
[tex]Q_{1-2} =w(h_{1} -h_{2} )[/tex]
[tex]Q_{1-2} =w_{cp} (t_{2} -t_{3} )[/tex]
[tex]Q_{1-2}[/tex] = 2xl.005(8000-150)
[tex]Q_{1-2}[/tex] = 1577.8kgj/s
Velocity at exit from the nozzle, assuming no heat loss.
Given t₁ = 150°C, t₂ = 8000°c
V₁ = 30m/s, V₂ = 30m/s
t₃ = 6500°C , V₃ = 60m/s
[tex]W(v_{2} )^{2} /2+h_{2} )=Wh_{3} + (v3)^{2} /2+Wt[/tex]
[tex](v2^{2}) -(v3^{2}) /2=(h2-h3)=Wt/w[/tex]
[tex](30^{2} -60^{2} )x10^{-3} /2+(1.005)(8000-6500)=Wt/w[/tex]
Wt = 1.506.15xw
Wt = 1506.15x2 = 3012.3kW
the enthalpy of air as h =cpt, where cp is the specific heat equal to 1. 005kJ/kg K and t is the temperature is 3012.3kW
To learn more about velocity refer to
https://brainly.com/question/25749514
#SPJ4
Struggling to stay faithful and remain attracted to my (34M) wife (28F) after we experienced a violent attack together. Not sure what to do.
The man's wife jumps in front of him to protect him from an attacker and has a scar on her face. The man finds his wife less attractive and "tries" to remain faithful to her. He is also annoyed that instead of spending the money to look better, she wants to keep it for her son.
What does money mean?
Currency is a commodity generally recognized as an economic medium of exchange. It serves as a means of expressing values and setting prices. It is the primary indicator of wealth as it moves from person to person and country to country. others that enable trade. According to economists, there are four basic types of money: commercial money, fiat money, fiat money, and commodity money. Commodity money is money whose value is derived from the commodities that compose it. Money is a centralized, widely used, and accepted form of exchange that facilitates the exchange of goods and services.
In economics, money is used as a medium of exchange for various goods and services.
To learn more about money refer to
brainly.com/question/24373500
#SPJ4
3. Soil has been compacted in an embankment at a bulk mass density rho of 2. 15 Mg/m^3 and water content w of 12%. Gs is 2. 65. Calculate dry mass density, void ratio, degree of saturation and air content. Would it be possible to compact this soil at w = 13. 5% to a dry mass density rhod of 2. 00 Mg/m^3?
S=110.07%, which is larger than 100% or full saturation. As a result, compact is impossible.
What is the soil compact ?[tex]$\gamma_b=2.15 \mathrm{Mg} / \mathrm{m}^3$[/tex]
[tex]$w=12 \%$\\$G_s=2.65$[/tex]
any list you can condense to [tex]$\omega=13.5 \%$[/tex]
[tex]r_d=2 \mathrm{Mg} / \mathrm{m} 3$$[/tex]
[tex]$\begin{aligned} \gamma d & =\frac{\gamma_b}{1+\omega} \\ & =\frac{2.15}{1+0.12}\end{aligned}$[/tex]
[tex]$\gamma d=1.919 \mathrm{Mg} / \mathrm{ms}^3$[/tex]
[tex]$\gamma_b=\frac{{Gs} \gamma \omega(1+\omega)}{1+e}$[/tex]
[tex]$2.15=\frac{(2.65)(1+0.12)}{1+e}$[/tex]
[tex]$e=0.38$[/tex]
[tex]$\begin{aligned} S & =\frac{w {Gos}}{e} \\ & =\frac{(0.12)(2.65)}{0.38}\end{aligned}$[/tex]
[tex]$S=83.68 \%$[/tex]
[tex]$\gamma_d=\frac{\left(1-n_a\right) G_{s \gamma_w}}{\left(1-h_a+w G_s\right)}$[/tex]
[tex]$h_a=0.165$[/tex]
[tex]$h _a=16.5 \%$[/tex]
Is it feasible to compact the aforementioned soil at a W=13.5 and [tex]$\gamma_d=2.00 \mathrm{Mg} / \mathrm{m} 3$[/tex]
[tex]$\begin{aligned} S & =\frac{\omega G_S}{e} \\ & =\frac{(0.135)(2.65)}{0.325} \times 100 \\ S & =110.07 \%\end{aligned}$[/tex]
[tex]$\begin{aligned} \text { rd } \quad & =\frac{{Cos} \delta \omega}{1+e} \\ 2 & =\frac{(2.65)}{1+e} \\ e & =0.325\end{aligned}$[/tex]
S=110.07%, which is larger than 100% or full saturation. As a result, compact is impossible.
To learn more about soil compact refer to :
https://brainly.com/question/21998342
#SPJ4
PS.52 The Station, a boutique cookie company, needs to create a production process for its new cinnamon malt ball cookies. To help accomplish this, the company has put together some numbers for production costs (per dozen cookies for the variable costs). Pre-Bake$150 Fixed Costs $1.75 Labor Costs $0.59 Material Costs Easy Bake$350 Fixed Costs $1.53 Labor Costs $0.48 Material Costs Speed Bake$550 Fixed Costs $1.35 Labor Costs $0.48 Material Costs The Station projects demand for the semester will be 450 dozen cinnamon malt ball cookies. Due to the cookies' expected popularity the selling price will be $4.49.A. Based on the projected demand (volume) for the semester, which process type should they select?1. Pre-Bake2. Easy Bake3. Speed BakeB. Under this process type—the one selected in the previous question—what would be their profits for the semester? (Display your answer to one decimal place.)C. If demand were to increase, what would be the break-even point (in unit volume or demand) between the selected process and the next process option? (Display your answer to two decimal places.)D. Beyond this break-even point, which process would be best?1. Pre-Bake2. Easy Bake3. Speed BakeE. Based on the break-even point (derived two questions back), what would be the total cost? (Display your answer to two decimal places.)
After an analysis of the costs, the demand, and the types of processes, the best cookie production option depends on the demand. Answer: If the demand is from 1 dozen to 600.06, pre-bake is selected, if it is greater, easy-bake. An image of the calculation procedures is attached
Which process type should they select?The best process type is the pre-bake because it has the greatest profits, as shown in the attached figure.
What would be their profits for the semester?For the pre-bake type process, the semester benefit is $817.50.
What would be the break-even point between the pre-bake and easy-bake process option?The semester demand would have to be 600.06 dozen cookies so that the pre-bake process is no longer the best option but easy-bake. Below is the solution algorithm.
Python codeif __name__ == '__main__':
fixed_cost_prebake = 150
fixed_cost_easybake = 350
variable_cost_prebake = 2.34
variable_cost_easybake = 2.01
sales_price = 4.49
profit_prebake = 0
profit_easybake = 0
sales = 0
while True:
sales = sales+0.01
profit_prebake = fixed_cost_prebake+(variable_cost_prebake*sales)
profit_easybake = fixed_cost_easybake+(variable_cost_easybake*sales)
if profit_prebake>=profit_easybake: break
sales = int(sales*100.0)/100.0
print("Break Even Point")
print("The demand would have to be: ",sales," so that pre-bake is no longer the best option but easy-bake")
Beyond this break-even point, which process would be best?When the demand is greater than 600.06 dozen, the best option is easy-bake process.
To learn more about analysis of the demand see: https://brainly.com/question/14570490
#SPJ4
essential for organoid development and growth is a media composition that recapitulates the in vivo stem cell niche signalling pathways, able to sustain stem cell function and drive their expansion and eventually their differentiation
Organoids are 3D cell aggregates that are created in vitro from primary tissue or stem cells and have the ability to self-renew, self-organize, and demonstrate organ functions.
How does organoid development work?Organoid production is akin to organism development, which starts with a zygote and results in a fully developed adult organism. A variety of mature tissues are produced as a result of tightly regulated differentiation, proliferation, and apoptosis in conjunction with multicellular self-organization and patterning.Organoids are 3D cell aggregates that are created in vitro from primary tissue or stem cells and have the ability to self-renew, self-organize, and demonstrate organ functions.Human embryonic stem cells (ESCs) or induced pluripotent stem cells (iPSCs) can be used in vitro to produce intestine organoids instead of isolated intestinal stem cells.To learn more about stem cells refer to:
https://brainly.com/question/21222769
#SPJ4
You are the IT administrator for a small corporate network. You're modifying the Power Plan settings for the laptop in the Executive Office.
In this lab, your task is to complete the following:
Set the following default settings for the power button action (all existing power plans):On battery: Hibernate Plugged in: Shut down Require a password on wakeup.
Set the computer to use a password on wakeup.
Select the High Performance power plan.
Modify the High Performance power plan settings as follows:
The process of modifying the Power Plan settings for the laptop in the Executive Office is called power optimization.
Power optimizationThe first step is to set the default settings for the power button action.When the laptop is on battery, it should be set to hibernate, and when plugged in, it should be set to shut down.Additionally, a password should be required on wakeup.The next step is to select the High Performance power plan.This plan should then be modified to the user's needs. This can be done by adjusting the settings for the display, sleep, and the hard disk.The display settings can be adjusted to lower the brightness and turn off the display after a certain amount of time.The sleep settings can be adjusted to put the computer to sleep after a certain amount of time of inactivity.Lastly, the hard disk settings can be adjusted to turn off the hard disk after a certain amount of time.These modifications will optimize the laptop's power usage and ensure that it is running efficiently.To learn more about Power optimization refer to:
https://brainly.com/question/18117915
#SPJ4
Power optimization is the process of changing the Power Plan settings for the laptop in the executive office.
Explain about the Power optimization?The power button action defaults are first established in the first stage.It should be configured so that the laptop shuts down when plugged in and goes into hibernation when running on battery.It should also be necessary to enter a password upon waking up.Picking the High Performance power plan is the following step.Following that, the user's needs should be incorporated into this plan. Changing the display, sleep, and hard disc settings will accomplish this.Lowering the brightness and setting a timer for the display to turn off can both be done by adjusting the display settings.To put the computer to sleep after a specific period of inactivity, the sleep settings can be changed.To learn more about Power optimization refer to:
https://brainly.com/question/18117915
#SPJ4
this bed load is what causes streams to abrade their streambed sand, and pebbles that are light enough to be picked up by the water and bounced along the bottom of the stream are moved in a process called .
The process is called traction or saltation.
What is traction or saltation?Traction or saltation is the process of sediment transport in which particles are moved by rolling or bouncing along the surface of the Earth. This process occurs when the wind, water, or ice apply enough force to the sediment particles to move them along the Earth's surface. The particles may roll, bounce, or slide along the surface.
This type of sediment transport is often seen in arid and semi-arid regions, where the wind is strong enough to move the particles, although it can also occur in areas with strong currents such as rivers and oceans.
Traction or saltation is one of three major processes of soil erosion, along with suspension and sheet erosion. It is most effective in carrying coarse-grained sediment, such as sand and gravel, while finer-grained sediment is usually carried away by suspension.
To learn more about traction or saltation refer :
brainly.com/question/30356900
#SPJ4
The rolling or dragging of large grains along a river bed or shore, aided by the push of smaller grains, is known as traction.
What is traction?Traction is a river transportation method for large stones or boulders. The water rolls the stones along the river bottom because they are too large to transport in the water.This type of sediment transport is common in arid and semi-arid regions where the wind is strong enough to move the particles, but it can also happen in areas with strong currents like rivers and oceans.Traction, along with suspension and sheet erosion, is one of the three major processes of soil erosion. It is most effective at transporting coarse-grained sediment, such as sand and gravel, whereas finer-grained sediment is usually transported by suspension.To learn more about traction refer to :
https://brainly.com/question/17370563
#SPJ4
given a string s of characters, a subsequence of s, defined by the indices i 1, i 2, ..., i m , is said to be a repeated subsequence if you can find another sequence of indices j 1, j 2, ..., j m, such that s[i k]
Answer:
= s[j k] for all 1 <= k <= m.
In other words, a repeated subsequence is a sequence of characters within the original string that appears in the same order at least twice. The indices i1, i2, ..., im refer to the positions of the characters in the original string that make up the repeated subsequence, and the indices j1, j2, ..., jm refer to the positions of the same characters in the second occurrence of the repeated subsequence.
when a technician purchases a gas furnace, it is set up to run on natural gas. a technician purchases a conversion kit. what would the technician expect to find in the conversion kit?
Answer:
A new burner orifices: These are small openings in the burner assembly that allow the correct amount of gas to flow into the furnace. The orifices in the kit will be different than the orifices in the natural gas furnace, as they are designed to work with the different pressure and flow rate of propane.
A new gas valve: The gas valve controls the flow of gas into the furnace. The gas valve in the conversion kit will be designed to work with propane, as it will have different pressure and flow characteristics than the natural gas valve.
A new regulator: This component reduces the pressure of the gas as it enters the furnace. The regulator in the conversion kit will be designed to work with propane, as it will have different pressure and flow characteristics than the natural gas regulator.
Instructions and documentation: The conversion kit should include detailed instructions and documentation on how to safely and correctly convert the furnace. This documentation should include all the necessary information such as safety precautions, tools needed, and step-by-step instructions.
In addition to the components mentioned above, the technician should also expect to find any additional parts or components that are required to complete the conversion process safely and efficiently. This can include, but not limited to, the venting system, any electrical components or wiring, and any additional hardware needed to complete the conversion.
It's important to note that the conversion process requires expert knowledge, skills and experience, and should only be carried out by a qualified and experienced technician. Additionally, the technician should follow the manufacturer's instructions and comply with local codes, regulations and safety standards
Functions and Design requirements• Select one device of your preference and write a primary function and at least 3 design requirements
I will select a smartphone as the device of my preference.
Primary function: A smartphone is a mobile device that allows users to make phone calls, send texts and emails, browse the internet, and use a variety of apps.
Design requirements:Durability: The device should be able to withstand everyday wear and tear, such as being dropped or bumped.
Battery life: The device should have a long-lasting battery that can last through a full day of heavy use.
Display: The device should have a high-resolution display that is easy to read in different lighting conditions.
User interface: The device should have an intuitive and user-friendly interface that is easy to navigate.
Read more about smartphones here:
https://brainly.com/question/25207559
#SPJ1
assume that a b and c are boolean variables that have been properly declared and initialized which of the following boolean expressions: (a && (b || !a)) == a && b
Which of the following best describes the conditions under which the expression will evaluate to true?
A Only when a is true
B Only when b is true
C Only when both a and b are true
D The expression will never evaluate to true.
E The expression will always evaluate to true.
boolean expressions C Just when a and b are accurate. If both requirements of a and b are met, the expression evaluates to true.
Only when both of the requirements in (a && (b ||!a)) == a && b are met does the expression (a && (b ||!a)) == a && b evaluate to true. This is as a result of the expression's use of the logical "AND" operator. Only when both of the conditions on which the "AND" operator is executing are true does it evaluate to true. The first condition in this situation is a && (b ||!a) and the second condition is a && b, both of which can only be satisfied when both a and b are true. As a result, only when both of the conditions for a and b are true does the phrase (a && (b ||!a)) == a && b evaluate to true.
Learn more about boolean expressions here:
https://brainly.com/question/13265286
#SPJ4
A circular bar supports an axial force of 39 KN. If the compressive stress in the bar is not to exceed
80 MN/m2, determine the diameter of the bar.
The diameter of the bar is 55.85 KN
What does "bar diameter" mean?A circular bar supports an axial force of 39 KN. If the compressive stress in the bar is not to exceed 80 MN/m2,
If you want to get the nominal diameter in inches, multiply the bar size by 80/39. For instance, the diameter of #8 rebar is 80/39 inches (or 1 inch). The weight, nominal area, and nominal diameter are common metrics.
The formula below may be used to determine the minimal diameter of round bar given the width and height of flat bar. Square Bar Minimum Diameter = Square Root of Flat Bar's Width and Height in Inches.
[tex]\sqrt{}[/tex]80 * 39 = 55.85
The diameter of the bar is 55.85 KN
To learn more about diameter refer to:
https://brainly.com/question/23220731
#SPJ4
a 200-ft-long section of a steam pipe whose outer diameter is 4 inches passes through an open space at 50 f. the average temperature of the outer surface of the pipe is measured to be 280 f, and the average heat transfer coecient on that surface is determined to be 6 btu/(h ft2 f). determine: (a) the rate of heat loss from the steam pipe (b) the annual cost of this energy loss if steam is generated in a natural gas furnace having an eciency of 86 percent,
Therefore, the annual cost of this energy loss can be calculated as: Cost = 1,531,200 * 0.86 * (Cost of natural gas per BTU) * 8760 = $XXXX.
The energy cost of the steam pipethe cost of natural gas is $10/mmbtua) The rate of heat loss from the steam pipe is:Q = hA(Tsurf - Tamb)
Q = (6 BTU/h ft2 F)(π*D*L)(280-50)
Q = (6 BTU/h ft2 F)(π*4 in * 200 ft)(230)
Q = 4,711,200 BTU/h
b) The annual cost of this energy loss is:Cost = (Q * 8760 hr/yr * $10/MMBtu)/(1,000,000 BTU/MMBtu)
Cost = (4,711,200 BTU/h * 8760 hr/yr * $10/MMBtu)/(1,000,000 BTU/MMBtu)
Cost = $39,690/yr
The rate of heat loss from the steam pipe can be calculated using the equation: Q = hAΔT, where Q is the rate of heat loss, h is the heat transfer coefficient, A is the surface area of the pipe, and ΔT is the difference between the average surface temperature (280F) and the ambient temperature (50F).The surface area of the pipe is A = π * (D/2)^2 * L, where D is the diameter of the pipe and L is the length of the pipe. Therefore, the rate of heat loss can be calculated as: Q = hAΔT = 6 (BTU/(h ft2 F)) * π * (4/2)^2 * 200 * (280-50) = 1,531,200 BTU/h.The annual cost of this energy loss can be calculated using the equation: Cost = Q * E * C * 8760, where Q is the rate of heat loss, E is the furnace efficiency, C is the cost of natural gas per BTU, and 8760 is the number of hours in a year.This is called the energy cost of the steam pipe.To learn more about the energy cost of the steam pipe refer to:
https://brainly.com/question/15632726
#SPJ4
As a result, the yearly cost of this energy loss may be computed as follows: Cost = 1,531,200 * 0.86 * (natural gas cost per BTU) * 8760 = $XXXX.
hieHow to get the solutionThe steam pipe’s energy cost
Natural gas costs $10 per mmbtu.
A)The heat loss rate from the steam pipe is:
Q = hA(Tsurf – Tamb)
Q = (6 BTU/h ft2 F)(π*D*L)(280-50)
Q = (6 BTU/h ft2 F)(π*4 in * 200 ft)(230)
Q = 4,711,200 BTU/h
b) The yearly cost of this energy loss is as follows:
Cost = (Q * 8760 hours per year * $10/MMBtu)/(1,000,000 BTU/MMBtu)
(4,711,200 BTU/h * 8760 hours per year * $10/MMBtu)/(1,000,000 BTU/MMBtu)
$39,690 per year
The following equation may be used to calculate the rate of heat loss from the steam pipe: Q = hAT, where Q is the heat loss rate, h is the heat transfer coefficient, A is the pipe surface area, and T is the difference between the average surface temperature (280F) and the ambient temperature (50F).
The surface area of the pipe is A = * (D/2)2 * L, where D is the pipe’s diameter and L is its length. As a result, the heat loss rate may be estimated as follows: Q = hAt = 6 (BTU/(h ft2 F)) * * (4/2)2 * 200 * (280-50) = 1,531,200 BTU/h.
The yearly cost of this energy loss may be computed as
Cost = Q * E * C * 8760,
where Q is the rate of heat loss,
E is furnace efficiency,
C is natural gas per BTU cost, and 8760 is the number of hours in a year.
This is referred to as the energy cost of the steam pipe.
To learn more about cost of energy to refer:
https://brainly.com/question/28795265
#SPJ4
a plane brick wall of a building has a thickness 100 mm and area of 5m2, has uniform, constant thermal conductivity (k) equal to 0.15 w/mk. given the outside temperature is 0 oc and the inside temperature is 20 oc. calculate the heat flux through the wall, thermal resistance of wall, and heat loss from the building through this wall under steady-state conditions.
Heat flux is the rate at which heat is conducted through a material over a given area.
Calculate the heat flux through the wall?
Heat Flux:
Heat flux through the wall = (20-0)* 0.15 * 5/100 = 0.9 W/m2
Thermal resistance:
Thermal resistance of wall = 100/0.15 = 667.7 m2K/W
Heat Loss:
Heat loss from the building through this wall = 0.9 * 5 = 4.5 W
Heat flux through the wall can be calculated using the formula, Q = kA(To-Ti)/L, where k is thermal conductivity (0.15 W/mK in this case), A is area of wall (5 m2), To is outside temperature (0 °C in this case), Ti is inside temperature (20 °C in this case), and L is thickness of wall (100 mm in this case). So, heat flux through the wall = 0.15 x 5 x (20-0) / 0.1 = 15 W.Thermal resistance of the wall is calculated using the formula, R = L/kA, where L is thickness of wall (100 mm in this case), k is thermal conductivity (0.15 W/mK in this case), and A is area of wall (5 m2). So, thermal resistance of wall = 0.1 / 0.15 x 5 = 0.33 K/W.Heat loss from the building through this wall is equal to the heat flux through the wall multiplied by the time, so the heat loss from the building through this wall is 15 W x t (time).To learn more about Thermal resistance refer to:
https://brainly.com/question/13258713
#SPJ4
The rate at which heat is transferred through a substance over a given area is referred to as heat flux.
How Determine the heat flux through the wall?Flux of Heat:
The heat flow through the wall is equal to (20-0)* 0.15 * 5/100 = 0.9 W/m2.
Thermal stability:
Wall thermal resistance = 100/0.15 = 667.7 m2K/W
Heat Absorption:
Heat loss via this wall from the building = 0.9 * 5 = 4.5 W
Q = kA(To-Ti)/L is the formula for calculating heat flow through a wall, where k is thermal conductivity (0.15 W/mK in this example), A is wall area (5 m2), To is outside temperature (0 °C in this case), Ti is inner temperature (20 °C in this case), and L is wall thickness (100 mm in this case). As a result, the heat flux through the wall equals 0.15.
The thermal resistance of a wall is determined using the formula R = L/kA, where L is wall thickness (100 mm in this example), k is thermal conductivity (0.15 W/mK in this case), and A is wall area (5 m2). As a result, the thermal resistance of the wall is 0.1 / 0.15 x 5 = 0.33 K/W.
The heat loss through this wall is equal to the heat flux through the wall multiplied by the time, hence the heat loss through this wall is 15 W x t. (time).
To learn more about Thermal resistance refer:
https://brainly.com/question/14785719
#SPJ4
Combining data from two or more relational database tables is an example of ________.A. collationB. responseC. reviewD. detection
Combining data from two or more relational database tables is an example of collation. Hence option A is correct.
What is the data Collation about?Joining is a process of combining data from two or more relational database tables based on a related column between them
Collation is a term used in the context of relational databases to refer to the process of combining data from two or more tables. This can be done through joining the tables on a common column, creating a new table that contains all the columns from the joined tables and the matching rows from each table.
Therefore, Collation is a way to combine data from multiple tables into a single result set.
Learn more about relational database from
https://brainly.com/question/13262352
#SPJ1
a diode for which the forward voltage drop is 0.7 v at 1.0maisoperatedat0.6v.whatisthevalueofthecurrent?
The current in this diode is 0.6 mA because the forward voltage drop of the diode is 0.7 V at 1.0 mA. When the voltage is decreased to 0.6 V, the current is also decreased to 0.6 mA.
A diode is an electronic component that allows current to flow in one direction only. It is made up of two terminals, an anode and a cathode, and is typically made of a semiconductor material such as silicon. Diodes are used in a variety of applications, such as rectifying AC to DC, providing voltage regulation, and protecting circuits from overvoltage. Diodes are also used in logic circuits, such as AND and OR gates, to control the flow of current. Diodes are typically made of a semiconductor material such as silicon. They are made up of two terminals, an anode and a cathode, and are designed to allow current to flow in one direction only. Diodes are used in a variety of applications, such as rectifying AC to DC, providing voltage regulation, and protecting circuits from overvoltage. Diodes are also used in logic circuits, such as AND and OR gates, to control the flow of current. Diodes can also be used to convert AC to DC, as well as to amplify signals. Diodes are also used in a variety of other applications, such as in light-emitting diodes (LEDs) and in photodiodes.
Learn more about Diodes here
https://brainly.com/question/12721595
#SPJ4
the curren in a 60hz single phase lags 36 degress bnehind the voltage calculate the time interval between the posotive peaks of voltage and current
The time interval between the positive peaks of the voltage and the current is (360 - 36) / (2 x 60) = 5.0 seconds.
voltage and current in an AC circuit
The theory used in this question is the phase angle difference between the voltage and current in an AC circuit. The phase angle difference is the difference in the timing of the positive peak of the voltage and the positive peak of the current.
In this case, the phase angle difference is 36 degrees, which means that the current lags the voltage by 36 degrees.
To calculate the time interval between the positive peaks of the voltage and current, we use the formula: (360 - phase angle difference) / (2 x frequency).
In this case, the frequency is 60 Hz, so the time interval between the positive peaks is 5.0 seconds.
The steps for this process are as follows:
Step 1: Calculate the phase difference between the voltage and current:
The phase difference between the voltage and current is the difference between the angles at which they peak.
In this case, the voltage peaks at 0 degrees and the current peaks at 36 degrees,
so the phase difference is 36 degrees.
Step 2: Calculate the frequency of the voltage and current:
The frequency of both the voltage and current is 60 Hz.
Step 3: Calculate the time interval between the positive peaks of the voltage and current:
The time interval between the positive peaks of the voltage and current is equal to the phase difference divided by the frequency multiplied by two.
This gives us (360 - 36) / (2 x 60) = 5.0 seconds.
To learn more about AC circuit refer :
brainly.com/question/30353024
#SPJ4
The time difference between the positive voltage and current peaks is 5.0 seconds.
What is voltage and current in an alternating current circuit?The phase angle difference between voltage and current in an alternating current circuit is the theory used in this question. The phase angle difference is the difference in the timing of the positive voltage peak and the positive current peak.Here,
The phase angle difference in this case is given as, 36 degrees, indicating that the current lags behind the voltage by 36 degrees.
The time interval between the positive peaks of voltage and current is calculated using the formula: (360 - phase angle difference) / (2 x frequency).
Because the frequency in this case is 60 Hz, the time interval between the positive peaks is 5.0 seconds.
The following are the steps for this procedure:
Step 1: Determine the phase difference of the voltage and current:
The phase difference between voltage and current is defined as the angle at which they peak.
The voltage peaks at 0 degrees and the current peaks at 36 degrees in this case.
As a result, the phase difference is 36 degrees.
Step 2: Determine the voltage and current frequencies:
Both the voltage and current have a frequency of 60 hertz.
Step 3: Determine the time interval between the voltage and current positive peaks:
The phase difference divided by the frequency multiplied by two equals the time interval between the positive peaks of voltage and current.
This results in a time of (360 - 36) / (2 x 60) = 5.0 seconds.
To learn more about current refer to :
https://brainly.com/question/6944790
#SPJ4
pick a big problem in your school or your community that you think could be solved with the help of computer science, robotics, or hardware engineering.
Computer science or robots can even predict human behavior, which can aid in crime prevention.
What are the uses of computer science?We can predict hurricanes, tornadoes, and even the outbreak of a potentially fatal disease using these tools. It can even be used to predict human behavior, which can aid in crime prevention. Computer science has the potential to provide us with life-saving tools and work.AI is at the forefront of the digital transformation that is being used to solve some of the world's most pressing problems.Computer science has enabled the development of sophisticated tools that can aid in the resolution of environmental issues. Computers can easily handle issues such as pollution, waste management and disposal, disease identification and containment, and others.Learning about computer science is important and beneficial to all students because it drives innovation, discovery, and even political participation.To learn more about computer science refer to :
https://brainly.com/question/20837448
#SPJ4
Need help to answer.
ASAP.
Steam at 20 bar, 3600C is expanded in a steam turbine to 0. 08 bar. It then enters a condenser, where it is condensed to saturated liquid water. A pump feeds back the water into the boiler.
(a) Assuming ideal processes, find per kg of steam the network and the cycle efficiency.
(b) If the turbine and the pump have 80% efficiency, find the percentage reduction in the network and cycle efficiency.
Assuming ideal processes, find per kg of steam the net work and the cycle efficiency 32.5%.
What is meant by processes ?
A process is a set of decisions and actions used to carry out work.Although we may not be aware of them, processes are present in every sphere of our lives, including work and pleasure.Several instances of processes might be: breakfast preparation. ordering something.Management is a process that unites limited human and material resources and inspires individuals to accomplish shared organisational goals. It is a series of continuing, complimentary actions rather than a single act.Every time a reader or listener processes a linguistic utterance, whether alone or in the context of a conversation or text, they are processing a sentence. The reading of isolated utterances (sentences) without context has been the focus of numerous studies on the human language comprehension process.h₁ = 3159.3KJ/kg
h₃ = [tex]h_{fp2}[/tex] = 173.88KJ/kg
[tex]h_{fgp2}[/tex] =2403.1KJ/kg
[tex]h_{fp}[/tex] = 0.001008m³/kg
S₁ = 6.9917 KJ/kgK
S₃ = [tex]s_{fp2}[/tex] = 0.5926 KJ/kgK
S[tex]_{gp2}[/tex] =8.2287 kJ/kgK
[tex]S_{fgp2}[/tex] = 7.6361 kJ/kgK
Now,
S₁ = [tex]S_{2} s[/tex]
= It is also written as or in the form of
S₁ = [tex]S_{2} s[/tex]
S₁ =[tex]s_{fp2}[/tex] + [tex]x2_{s} S_{fgp2}[/tex] = 0.5926 + x₂ × 7.6361
from this we have to find the value of
[tex]x2_{s}[/tex]= 6.3991 / 7.6361 = 0.838
∴[tex]h_{2s} -h_{fp2} +x2_{s} h_{fgp2} =[/tex] = 173.88 + 0.838 × 2403.1 = 2187.68KJ/kg
[tex]Wp=h_{4s} -h_{3} =U_{fp2} (p1-p2)[/tex]
= 0.001008 m³/kg x 19.92 xl00 KN/m²
= 2. 008 K/Kg
[tex]h_{4s} =[/tex] 175.89 KJ/kg
[tex]W_{T} =h_{1} -h_{2s}[/tex]
= 3159.3 - 2187 68
= 971.62 KJ/kg
[tex]W_{net} =W_{T} -W_{p}[/tex] = 969.61 KJ/kg
[tex]Q_{1} =h_{1} -h_{4s}[/tex] = 3159.3- 175.89
= 2983.41 KJ/kg
[tex]n_{cycle} = W_{net} / Q1 =[/tex] 969.61 81 / 2983.41 = 0.325 or 32.5%
b) If [tex]np_[/tex] = 80% and = 80%
[tex]W_{p}[/tex] = 2.008 / 0.8 = 2.51 kJ/kg
[tex]W_{T}[/tex] = 0.8 X 971.62 = 777.3 kJ/kg
[tex]W_{net} = W_{T} -W_{P}[/tex] = 774.8 KJ/kg
∴ % Reduction in work output = (969.61 -774.48) /969.61 * 100 = 20.1%
[tex]h_{4s}[/tex] = 173.88 + 2.51 = 176.39 KJ/kg
[tex]Q_{1}[/tex] = 3159.3 - 176.39 = 2982.91 KJ/kg
[tex]n_{cycle}[/tex] = 774.8 / 2982.91 = 0.2597 or 25.97%
∴ % Reduction in Cycle efficiency = 0.325-0.2597/0.325 * 100 = 20.1%
To learn more about processes refer to
https://brainly.com/question/28523445
#SPJ4
what is the most important step in safely changing lanes
Answer:
The most important step in safely changing lanes is to check your mirrors and do a shoulder check to ensure it is safe to do so. This includes checking for vehicles in your blind spot, as well as checking for any pedestrians, bicycles, or other obstacles that may be in the way.
The most critical step in safely changing lanes is checking your blind spots. It's an area that your mirrors cannot cover and so you have to briefly look over your shoulder to ensure there's no vehicle in that space before changing lanes.
Explanation:The most important step in safely changing lanes is to check your blind spots. This is significant because there might be another vehicle or obstacle in the area of the road you cannot see either through your peripheral vision or rear-view mirrors. Here are the steps you should follow when changing lanes:
Turn on your signal to indicate your intention to other drivers.Check your rear-view mirror and side mirrors to see if the lane is clear.Next, check your blind spot. This is done by briefly looking over your shoulder in the direction you intend to move.Only when you’re sure the lane is clear, carefully change lanes.Make sure to revert to your original lane once you have completed the maneuver.Learn more about Changing lanes safely here:https://brainly.com/question/31918423
#SPJ6
you are the network administrator for a branch office of a larger organization. your branch is adding a new wireless network into an existing branch office lan. the existing network is configured to exchange routes using ospfv2 in a single-area configuration. your task is to verify the operation of the existing ospfv2 network, before adding in the new lan. when you are sure that the current ospfv2 lan is operating correctly, you will connect the new lan and verify that ospf routes are being propagated for the new lan. as branch office network administrator, you have full access to the ios on routers r3 and r4. you only have read access to the enterprise lan routers r1 and r2, using the username branchadmin, and the password branch1234.
One of those is accurate since the two routers cannot become neighbors because they have the same OSPF router ID (RID).
An OSPFv2 router broadcasts a distinct message, known as a hello packet, out each OSPF-enabled interface in order to identify other OSPFv2 neighbor routers. Following the discovery of a neighbor, the two routers compare information from the hello packet to determine whether their configurations are compatible. The default network type for an Ethernet interface that supports OSPF is the broadcast network type. A connection capable of supporting Layer 2 broadcast is required. Neighbors are two or more routers sharing an interface in a shared network, such as two routers connected via a point-to-point serial link. One of those is accurate since the two routers cannot become neighbors because they have the same OSPF router ID (RID).
Learn more about Router here:
https://brainly.com/question/29511214
#SPJ4
n this lab, you task is to diagnose and correct the problem. use the following steps to walk through the troubleshooting process: press the power button on the computer to verify that it will not start. select the motherboard and view the specifications to identify the location of the cpu socket and fan power connector. answer question 1. close the motherboard specs and verify that the cpu heat sink and fan assembly is installed. answer question 2. answer question 3. based on your findings, you will need to replace the cpu. temporarily remove the heat sink and fan to the workspace.
An approach to problem solving called troubleshooting is frequently used to fix broken components or operations on a machine or a system.
What are the 7 troubleshooting steps?The next seven steps are frequently employed during troubleshooting, however troubleshooting approaches differ.Acquire knowledge.Write about the issue.The most likely reason should be determined.Making a plan of action and putting a fix to the test.Activate the solution.Speculate on the findings.Make a process record. In order to discover the source of the aforementioned situation, one must first establish a theory of probable causation, test that theory, and then follow the steps outlined above once they have done so.Computer troubleshooting is a term that refers to a methodical approach to problem-solving that is stated to be frequently used to identify and resolve problems with sophisticated machinery, electronics, computers, and software systems.To learn more about troubleshooting refer
https://brainly.com/question/28508198
#SPJ4
for his position as a lead mechanic, jeff needs to know when and how to use a 12 millimeter screwdriver and a 14 millimeter screwdriver for a specific task. this requires
Technical Knowledge is the understanding of the specific tools, techniques, and processes required to complete a task. In this case, Jeff needs to have a thorough understanding of when and how to use a 12 millimeter screwdriver and a 14 millimeter screwdriver for a specific task.
This requires him to have a deep understanding of the tools and techniques require completing the task, as well as the processes involved in using the tools correctly. Jeff must also be able to identify any potential risks or issues that may arise during the task and take steps to mitigate them. Additionally, Jeff must be able to troubleshoot any problems that may arise during the task and take the necessary steps to resolve them. Jeff must also be able to identify any potential safety hazards associated with the task and take steps to ensure that they are addressed. Jeff must be able to provide regular updates to his supervisor on the progress of the task and ensure that any changes or modifications are communicated in a timely manner. Finally, Jeff must be able to provide feedback and advice to his supervisor in order to ensure that the task is completed successfully.
Learn more about Technical Knowledge here
https://brainly.com/question/25053983
#SPJ4
arrange the tasks in the correct sequence, based on the proper usage and maintenance of knives. store the clean knife in the knife block. clean the knife after use. select the proper knife for the job. purchase the required knives.
The correct sequence for proper usage and maintenance of knives is as follows:
1. Purchase the required knives. 2. Select the proper knife for the job. 3. Clean the knife after use. 4. Store the clean knife in the knife block.
Purchasing the required knives is the first step in the proper usage and maintenance of knives. It is important to select the right knives for the job, as different knives are designed for different tasks. After use, it is important to clean the knife to prevent the spread of bacteria and to keep the knife in good condition. Finally, the clean knife should be stored in a knife block to protect it from damage and to keep it organized.
Learn more about sequence here
https://brainly.com/question/30262438
#SPJ4
Draw shear Force and bending moment diagram for the beam given below.
The primary purpose of beams as structural components is to support vertical loads.
What is Force and bending moment?The highest shear and maximum moment locations, as well as the corresponding magnitudes, should be noted while constructing a beam because there is where the structure is most likely to break.
We must measure the shear force and bending moment at every location along the whole length of the beam in order to identify these important places. The method to determine the shear and bending moment at a single location was described in the previous part.
While this method is helpful, you will need a more potent strategy to determine the shear and moment at every point in the item. A shear and bending moment diagram can be made to do this.
Therefore, The primary purpose of beams as structural components is to support vertical loads.
To learn more about Bending moment, refer to the link:
https://brainly.com/question/30242055
#SPJ1
in this diode circuit, what is the value of the load voltage v subscript r for v subscript i equals minus 5 v and v subscript i equals space 5 v? assume si diode with v subscript d 0 end subscript equals 0.7 space v. instructions: assume an on or off state for the diode and using the developed piecewise linear model for the diode, write the corresponding diode current and voltage equations for each state. write a kvl for the circuit and find the diode voltage and current. use the inequality in the piecewise linear model to check the calculated diode current or voltage values. the above steps should be repeated for each one of the given vi values. after you solved the problem, choose the option that has the correct statement. the statements in three out of four options are incorrect.
As a formula for current as a function of voltage, the ideal diode equation is quite helpful.When the ideal diode equation is reversed and used to solve for voltage as a function of current, we discover that v(i)=VTln[(iIS)+1).
How do you calculate the value of a diode?As a formula for current as a function of voltage, the ideal diode equation is quite helpful.When the ideal diode equation is reversed and used to solve for voltage as a function of current, we discover that v(i)=VTln[(iIS)+1). However, there are occasions when the inverse relationship may be more helpful.The voltage drop across the load when several diodes are connected in series is equal to (supply voltage - the number of diodes * 0.7).Taking figure 1 as an example, the voltage drop across the diode D1 is (5.0.7) = 4.3 V.D2 has a voltage drop of (5-2 * 0.7) = 3.6 V.Only the forward direction, also known as current flow, is allowed through a diode.To learn more about ideal diode equation refer
https://brainly.com/question/14894948
#SPJ4
Carbon steel (AISI 1010) shafts of 0. 1 - m diameter are heat treated in a gas - fired furnace whose gases are at 1200 K and provide a convection coefficient of 100 W/m2,K. If the shafts enter the furnace at 300 K, how long must they remain in the furnace to achieve a centerline temperature of 800 K?
800 K's center line temperature must be attained in t = 58 seconds.
Explain about the centerline temperature?The normalized centerline temperature is determined by where the horizontal line crisscrosses the y-axis. Now, we'll use the second chart to determine the temperature at any point within the solid.
Following is the fundamental data: Surface energy balance equation, first: H = Rn - G - L. E, where H denotes the sensible heat flow from surface to air, Rn denotes net radiation to the surface, G denotes the heat absorbed into the soil, L denotes the latent heat of evaporation, and E denotes the rate of evaporation.
The temperature gradient of a heated body in a steady condition is defined as the ratio of the temperature difference to the distance between two places.
Given data
D = 0.1 m
h = 100
Carbon steel's specific heat (C) is 502.4.
1200 K is the furnace temperature.
800 K is the final temperature.
300 K at initial temperature
From the equation now (1)
㏑ 0.44 = -(0.001415 ) t
-(0.001415 ) t = - 0.82
t = 58 sec
To learn more about centerline temperature refer to:
https://brainly.com/question/16398731
#SPJ4
etermine fcg and fgh , the magnitudes of the forces in members cg and gh, respectively, using the method of sections. assume for your calculations that each member is in tension, and include in your response the sign of each force that you obtain by applying this assumption.
All forces are pulling away from the thing when it is in tension. The pressures on the material push towards the direction of the body during compression.
A rope bridge can support both itself and its weight thanks to tension forces that pull and stretch material in opposing directions. Arch bridge rocks are forced to press against one another in order to support the weight due to compression pressures that squeeze and push material inward. Members can only be in compression or tension. When anything is under stress, all forces are repelled from it. When a material is compressed, the forces acting on it cause it to move in the direction of the body. Pulling on the ends of the object will increase the tension. All forces are pulled away from the object under tension, which is related to shifting the body's borders toward the centre. The pressures on the material push towards the direction of the body during compression.
Learn more about Compression here:
https://brainly.com/question/30115684
#SPJ4
A rectangular steel bar 38 mm wide and 25 mm deep is subjected to a torque of 450 Nm Estimate the maximum shear stress set up in the material of the bar and the angle of twistWhat percentage error would be involved in each case the approximate equations are used? For steeltake G = 80; GN / m * 2
Answer:
The maximum shear stress set up in the material of the bar is:
τmax = 450 Nm / (0.038 m * 0.025 m) = 59.2 MPa
The angle of twist is:
θ = 450 Nm * (0.038 m^3) / (3 * 80 GN/m^2 * 0.025 m^2) = 0.0024 rad
The percentage error when using the approximate equations would be approximately 8.7%.