Answer:
1.4 m/s to the left
Explanation:
just took it c:
Who was the first who traveled to the moon?
NEIL ARMSTRONG WAS THE FIRST MAN WHO TRAVELLED TO THE MOON.
Answer:
On July 20, 1969, Neil Armstrong became the first human to step on the moon.
A force of 15 newtons is used to push a box along the floor a distance of 3 meters. How much work was done?
Answer:
The answer is 45 JExplanation:
The work done by an object can be found by using the formula
workdone = force × distanceFrom the question
distance = 3 meters
force = 15 newtons
We have
workdone = 15 × 3
We have the final answer as
45 JHope this helps you
How do I proton and and electron compared
A ray is incident at at 50 degrees angle on a plane mirror. What will be the deviation after reflection from the mirror?
Answer:
Explanation:
If the ray were not deviated, it would travel straight through the mirror. Due to the mirror, the incident ray is reflected at 30°. The ray travels 30° + 30° = 60°. The angle of deviation is 180° - 60° = 120°.
What is the maximum current flow possible through a 12 Ohm resistor from a 120V source?
Answer:
I=10.0A
Explanation:
V=RI(120)=(12)II=10.0AA solid nonconducting sphere of radius R carries a charge Q distributed uniformly throughout its volume. At a certain distance rl (r
(A) E/8
(B) E 78.
(C) E/2
(D) 2E
(E) 8E
Answer:
A ) E/8
Explanation:
If the sphere of radius R carries charge Q, then the volumetric charge density is:
ρ₁ = [Q/ (4/3)*π*R³]
Therefore the net charge inside r ( r < R ) is:
q₁ = ρ * (4/3)*π*r³
And E = K * q₁/r K = 9,98 *10⁹ [N*m²/C²]
E = K * ρ * (4/3)*π*r³/r
E = K * ρ * (4/3)*π*r²
If now the charge is distributed over a sphere of radius 2R
ρ₂ = [Q/ (4/3)*π*(2R)³]
ρ₂ = [Q/ (4/3)*π*8*R³]
Then ρ₂ < ρ₁ in fact ρ₂ = (1/8)*ρ₁
The electric field depends on the net charge enclosed by a gaussian surface, and the distance between the net charge and the considered point, ( considering the net charge as being at the center of the gaussian surface) In this case, there was no distance change then
E₂ = E₁/8
The right answer is lyrics A ) E/8
A car at the top of a ramp starts from rest and rolls to the bottom of the ramp, achieving a certain final speed. If you instead wanted the car to achieve twice as much speed at the bottom of the ramp, how high should the ramp be compared to the first case
Answer:
It must be 4 times high.
Explanation:
Assuming that the car can be treated as a point mass, and that the ramp is frictionless, the total mechanical energy must be conserved.This means, that at any time, the following must be true:ΔK (change in kinetic energy) = ΔU (change in gravitational potential energy)⇒ [tex]m*g*h = \frac{1}{2} * m*v^{2}[/tex]
Let's call v₁, to the final speed of the car, and h₁ to the height of the ramp.So, at the bottom of the ramp, all the gravitational potential energy
must be equal to the kinetic energy of the car (Defining the bottom of
the ramp as our zero reference for the gravitational potential energy):
[tex]m*g*h_{1} = \frac{1}{2} * m*v_{1} ^{2}[/tex] (1)
Now, let's do v₂ = 2* v₁Replacing in (1) we get:[tex]m*g*h_{2} = \frac{1}{2} * m*(2*v_{1}) ^{2}[/tex] (2)
Dividing (2) by (1), and rearranging terms, we get:h₂ = 4* h₁Determine the electrical force of attraction between two balloons
that are charged with the opposite type of charge but the same
quantity of charge. The charge on the balloons is 6.0 x 10-7 C and they
are separated by a distance of 0.50 m.
Answer:
F=1.3x10^-2N
Explanation:
Fe= k(6x10^-7C)^2/(0.5)^2
Electrical force of attraction between the balloons is F=1.3x10^-2N
The electric force of attraction between two balloons should be F=1.3x10^-2N.
Calculation of the electric force;Since The charge on the balloons is 6.0 x 10-7 C and they are separated by a distance of 0.50 m.
So, here the electric force is
Fe= k(6x10^-7C)^2/(0.5)^2
F=1.3x10^-2N
hence, The electric force of attraction between two balloons should be F=1.3x10^-2N.
Learn more about force here: https://brainly.com/question/19848845
Please provide explanation!!!
Thank you.
Answer:
(a) 102 cm/s
(b) 0.490 cm²
Explanation:
(a) Use Bernoulli equation.
P₁ + ½ ρ v₁² + ρgh₁ = P₂ + ½ ρ v₂² + ρgh₂
0 + ½ ρ v₁² + ρgh₁ = 0 + ½ ρ v₂² + 0
½ ρ v₁² + ρgh₁ = ½ ρ v₂²
½ v₁² + gh₁ = ½ v₂²
½ (25.0 cm/s)² + (980 cm/s²) (5.00 cm) = ½ v²
v = 102 cm/s
(b) The flow rate is constant.
v₁ A₁ = v₂ A₂
(25.0 cm/s) (2.00 cm²) = (102 cm/s) A
A = 0.490 cm²
(iii) Why do right angle mirrors produce three images of the object?
Explanation:
The two mirrors inclined to each other formed the first two images with are of the same size as the object while the third mirror is produced from the intersection of rays that emanated during the production of the first two images to produce a third image which is smaller than the object and there making the total number of images to be 3.
Hence this mirrors produces 3 images due to the third image formed from the intersection of the rays that produces the first two images.
The formula that relates the image produced by inclined mirror and the angle of inclination is expressed as:
number of images n = 360/θ - 1
θ is the angle of inclination of the two mirrors
n is the number of images
If the mirrors are inclined at right angles, then θ = 90°
Substitute into the formula;
n = 360/90 -1
n = 36/9 -1
n = 4-1
n = 3
A "lovesick" individual wants to throw a bag of candy and love notes into the open window of their significant other’s bedroom 10.0 m above. Assuming it just reaches the window, they throw the gift at 60.0o to the ground: At what velocity should they throw the bag? How far from the house are they standing when they throw the bag? (Answer: A. 16.2m/s B. 11.5m)
Answer:
Explanation:
Let the velocity be v .
vertical component of the velocity = v sin 60 = √3 v /2
it reaches maximum height of 10 m .
v² = 2 gh
( √3 v/2 )² = 2 x 9.8 x 10
3 v² = 196 x 4
v² = 65.33 x 4
v = 16.2 m /s
Let time taken to reach height of 10 m
v = u - gt
v sin 60 = 9.8 t
16.2 x √3 /2 = 9.8 t
t = 1.43 s
horizontal distance covered = v cos 60 x t
16.2 x .5 x 1.43 = 11 .5 m
A fountain shoots a jetof water straight up. The nozzle is 1 cm in diameter and the speed of the water exiting the nozzle is 30 m/s. What is the force exerted by the water jet
Answer:
Explanation:
mass of water coming out per second = A x v where A is area of cross section of the nozzle and v is velocity of water
A = 3.14 x .005²
= 785 x 10⁻⁷ m²
mass of water coming out per second = 785 x 10⁻⁷ x 30 = 23.55 x 10⁻⁴ kg
momentum of this mass = 23.55 x 10⁻⁴ x 30 = 706.5 x 10⁻⁴ kg m /s .
Rate of change of momentum = 706.5 x 10⁻⁴
Let force be F
F - mg = 706.5 x 10⁻⁴
F = mg + 706.5 x 10⁻⁴
F = 23.55 x 10⁻⁴ x 9.8 + 706.5 x 10⁻⁴
= 937.3 x 10⁻⁴ N .
The Intensity level of a loud saw is 100 db at a distance of 5m. At what distance would the level be 80 db
Answer:
50 m
Explanation:
The relationship between the intensity of sound in dB and distance is given by the formula:
[tex]B_2=B_1+20log(\frac{R_1}{R_2} )\\\\Where \ B_2\ is \ the\ sound\ intensity\ at\ distance\ R_2\ and\\B_1\ is \ the\ sound\ intensity\ at\ distance\ R_1\ \\\\Given\ that: B_1=100\ dB, R_1=5\ m, B_2=80\ dB\\\\B_2=B_1+20log(\frac{R_1}{R_2} )\\\\80=100+20log(\frac{5}{R_2} )\\\\-20=20log(\frac{5}{R_2} )\\\\log(\frac{5}{R_2} )=-1\\\\\frac{5}{R_2}=10^{-1}\\\\\frac{5}{R_2}=0.1\\\\R_2=5/0.1=50\ m[/tex]
A person following a liberal ideology would likely approve of
An airplane, starting at rest, takes off on a 600. m long runway accelerating at a rate of 12 m/s/s. How many seconds does it take to reach the end of the runway?
Answer:
10 seconds
Explanation:
As it starts from rest, then u=0
and by III rd equation of motion:
An electron moving in the direction of the x-axis enters a magnetic field. If the electron experiences a magnetic deflection in the -y direction, the direction of the magnetic field in this region points in the direction of the
Answer:
-z
Explanation:
The force on a moving charge due to a magnetic field follows the right hand rule, so a positive charge, experiencing a magnetic deflection in the -y direction, while it moves in the direction of the x-axis, will do it due to a magnetic field pointing in the +z direction.
As the electron has a negative charge, the magnetic field will point in the opposite direction, i.e., in the -z direction.
How many turns are in its secondary coil, if its input voltage is 120 V and the primary coil has 210 turns
Complete Question
How many turns are in its secondary coil, if its input voltage is 120 V and the primary coil has 210 turns.
The output from the secondary coil is 12 V
Answer:
The value is [tex]N_s = 21 \ turns [/tex]
Explanation:
From the equation we are told that
The input voltage is [tex]V_{in} = 120 \ V[/tex]
The number of turns of the primary coil is [tex]N_p = 210 \ turn[/tex]
The output from the secondary is [tex]V_o = 12V[/tex]
From the transformer equation
[tex]\frac{N_p}{V_{in}} =\frac{N_s}{V_o}[/tex]
Here [tex]N_s[/tex] is the number of turns in the secondary coil
=> [tex]N_s = \frac{N_p}{V_{in}} * V_s[/tex]
=>[tex]N_s = \frac{210}{120} * 12[/tex]
=>[tex]N_s = 21 \ turns [/tex]
3 For this force system the equivalent system at P is ___________ A FRP 40 lb along x dir and MRP 60 ft lbB FRP 0 lb and MRP 30 ft lbC FRP 30 lb along y dir and MRP 30 ft lbS FRP 40 lb along x dir and MRP 30 ft lb
This question is incomplete, the complete question is;
For this force system the equivalent system at P is ___________
A) FRP = 40 lb (along +x-dir.) and MRP = +60 ft.lb
B) FRP = 0 lb and MRP = +30 ft.lb
C) FRP 30 lb (along +y-dir.) and MRP = -30 ft.lb
D) FRP 40 lb (along +x-dir.) and MRP = +30 ft.lb
Answer:
D) FRP 40 lb (along +x-dir.) and MRP = +30 ft.lb
Explanation:
From the figure in the image i uploaded along this answer;
FRP = ( 40 lb i + 30 lb j ) + [30 lb (-j)]
Where i and j are the unit vectors along X & Y axis respectively.
So, FRP = 40 lb i
that is, FRP = 40 lb along +X direction
MRP = [ 30 lb x ( 1 ' + 1' ) ] +( -30 lb x 1 ' )
= (30 lb x 2 ' )- 30 lb ft
= 60 lb ft - 30 lb ft
= 30 lb ft
Therefore option(D) is correct
What is the approximate weight of a 400 kg object?
Answer:
881.84905 LBS
Explanation:
ThErE :p
3922.66 newtons.
This is an exact amount, to get newtons form kg, multiply by 9.8, or in this case, 10.
This gives you 4000 newtons
Calculate the effective charges on the H and F atoms of the HF molecule in units of the electronic charge, e.
Answer:
Explanation:
Hydrogen fluoride (HF) is an ionic/electrovalent compound that dissociates into ions when dissolved in water. It's dissociation is as seen below
HF ⇄ H⁺ + F⁻
There is a transfer of electron from the hydrogen atom which produces the hydrogen ion (H⁺), while the fluorine atom receives the donated ion to become negatively charged (F⁻). The amount of charge in one electron is generally given as 1.602 × 10⁻¹⁹ coloumbs.
The required value of effective charge on HF molecule, due to H and F is 1.602 × 10⁻¹⁹ Coulombs.
The given problem is based on the concept of effective charges. The net positive charge carried out by the electrons of atomic species, after forming a polyelectronic atom is known as Effective charge.
As per the given problem, the Hydrogen fluoride (HF) is an ionic/electrovalent compound that dissociates into ions when dissolved in water. It's dissociation is given as,
HF ⇄ H⁺ + F⁻
There is a transfer of electron from the hydrogen atom which produces the hydrogen ion (H⁺), while the fluorine atom receives the donated ion to become negatively charged (F⁻). The amount of charge in one electron is generally given as 1.602 × 10⁻¹⁹ Coulombs.
Thus, we can conclude that the required value of effective charge on HF molecule, due to H and F is 1.602 × 10⁻¹⁹ Coulombs.
Learn more about the effective charge here:
https://brainly.com/question/25002720
In each of the given pairs, choose which element will have the bigger atom. Give reasons for your choice. (a) Mg (atomic number 12) or Cl (atomic number 17) (b) Na (atomic number 11) or K (atomic number 19)
Answer:
Mg (atomic number 12)
K (atomic number 19)
Explanation:
The size of an atom is estimated in terms of its atomic radius.
The atomic radius is taken as half of the inter-nuclear distance between two covalently bonded atoms of non-metallic elements or half of the distance (d) between two nuclei in the solid - state of metals.
Across a period, atomic radii decrease progressively from left to right. This is due to the progressive increase in the nuclear charge without increase in the number of electronic shells. Down a group, atomic radii increase progressively due to the successive shells of electrons being added which have been compensated for by the increase in nuclear charge.Cl is further right of Mg in the third period
K is below Na in the first group
SOH-CAH-TOA is used to solve for the ________
velocities in a full/angled projectile.
a. final (x and y)
b. overall
c. initial (x and y)
d. resultant
Answer:
c. initial (x and y)
Explanation:
When a projectile is launched at a velocity with a launch angle, to solve it, we must first resolve the initial velocity into the x and y components. To do this will mean we have to treat it like a triangle due to the launch angle and the direction of the projectile.
Therefore, we will have to make use of trigonometric ratios which is also known by the mnemonic "SOH CAH TOA"
Thus, this method resolves the initial x and y velocities.
A chef places an open sack of flour on a kitchen scale. The scale reading of
40 N indicates that the scale is exerting an upward force of 40 N on the sack. The magnitude of this force equals the magnitude of the force of Earth’s gravitational attraction on the sack. The chef then exerts an upward force of
10 N on the bag and the scale reading falls to 30 N.Draw a free-body diagram of the latter situation.
Answer:
Explanation:
Given
Initial reading on scale =40 N
So, we can conclude that weight of the sack is 40 N
After this a 10 N force is applied upward on the sack such that the net force becomes (40-10) N downward (because downward force is more)
This net downward force is the resultant of earth graviational pull and the applied upward force.
So, this downward force acts on the machine which inturn applies an upaward force of same magnitude called Normal reaction.
This situation can be diagramatically represented by figure given below
Answer:
40N
Explanation:
trust
Peter is running laps around a circular track with a diameter of 100 meters. If it takes Peter 12 minutes to run 4 laps, how quickly is he running (in meters per second)?
Answer:
v = 1.74 m/s
Explanation:
Given that,
Diameter of a circular track, d = 100 m
Distance covered for the 4 laps,
[tex]D=4\pi d\\\\D=4\pi \times 100\\\\D=1256.63\ m[/tex]
Time, t = 12 minutes = 720 s
We need to find the velocity of the peter. It can be calculated as follows :
[tex]v=\dfrac{D}{t}\\\\v=\dfrac{1256.63\ m}{720\ s}\\\\v=1.74\ m/s[/tex]
So, the speed is running with a velocity of 1.74 m/s.
Peter is running at 1.7453 m/sec.
Given to us,
Diameter of the circular track, D = 100 meters,
Number of laps Peter run, L = 4 laps,
Time taken by Peter, t = 12 minutes,
1 lap = circumference of the circle,
4 laps = 4 x circumference of the circle,
As we know, the circumference of a circle is given by πD.
So, 4 laps = 4 x circumference of the circle,
[tex]\begin{aligned}4 laps &= 4\times \pi \times D\\&= 4 \times \pi \times 100\\& = 1,256.6370\ meters\\\end{aligned}[/tex]
Also, we know that 1 minute has 60 sec.
so, 4 minutes = (4 x 60) seconds
Further, speed is given [tex]\bold{(\dfrac{Distance}{Time} )}[/tex]
Thus,
[tex]\begin{aligned}speed &= \dfrac{Distance\ coverd\ by\ Peter}{Time\ taken\ by\ Peter}\\&=\dfrac{1,256.6370}{12\times 60}\\&=1.7453\ m/sec \end{aligned}[/tex]
Hence, Peter is running at 1.7453 m/sec.
To know more visit:
https://brainly.com/question/7359669
A recipe gives the instructions below
After browning the meat pour off fat from the pan to further reduce fat use a strainer.
what type lf separation methods are described in the recipe
A decantation and screening
B distillation and screening
C decantation and centrifugation
D distillation and filtration
Answer:
A. decantation and screening
Explanation:
Decantation is the one of the process of separating the mixture. In this process the precipitated liquid is separated from the solid. According to the given instruction for the recipe, the fat which is in liquid state is separated from meat. In the process of screening, more liquid is separated by placing the mixture on the screen. Here, the gravity plays an important role for the process of separation.
Answer:
a
Explanation:
A curve that has a radius of is banked at an angle of . If a -kg car navigates the curve at without skidding, what is the minimum coefficient of static friction between the pavement and the tires
Answer:
0.65
Explanation:
For whatever reasons, the parameters are not giving. So, I will assume by myself to make the calculations easier. You can substitute whatever it is to it from your question.
Given that
Radius of the road, r = 63 m
Speed of the car, v = 20 m/s
The relationship between a car that is passing through a curve and it's frictional force is said to be
U(s) * g = v²/r
In the formula above,
U(s) = coefficient of static friction
g = acceleration due to gravity, 9.8 m/s²
v = velocity of the car
r = radius of the road
Now when we substitute the earlier stated values, we have
U(s) * 9.8 = 20² / 63
U(s) * 9.8 = 400 / 63
U(s) * 9.8 = 6.35
U(s) = 6.35 / 9.8
U(s) = 0.65
Thus, our coefficient of static friction, based on the stated values is 0.65
Who ever answers first get Brainliest!
How is power passed down in a dynasty?
through a family bloodline
through a religious council
through an arranged marriage
through a military commander
A car starts from rest and accelerates for 7.2 s with an acceleration of 1.4 m/s2. How far does it travel? Answer in units of m.
Answer:
xn = 36.28 [m]
Explanation:
To solve this problem we must use the following equation of kinematics, which is ideal for a body that moves with constant acceleration.
[tex]x=x_{0}+(v_{o} *t)+(\frac{1}{2} )*a*t^{2}[/tex]
where:
x - xo = displacement of the car [m]
Vo = initial velocity = 0
t = time = 7.2 [s]
a = acceleration = 1.4 [m/s^2]
The initial velocity is zero, as the car begins its movement from rest.
xn = (x - xo), Now replacing
xn = (0*7.2) + 0.5*1.4*(7.2^2)
xn = 36.28 [m]
waht is science
wjwissbsskdldmndndnd
Answer:
the intellectual and practical activity encompassing the systematic study of the structure and behaviour of the physical and natural world through observation and experiment.
Explanation:
Please help
A student plans an investigation to determine the refractive index of glass. The student uses this equipments.
- a ray box
- a rectangular glass block
- a protractor
- a pencil
Describe how the student collect her data.