2.3. Provide the weathering products of the following minerals.
2.3.1 Feldspar
2.3.2 Pyrite
2.4. Distinguish between Breccia and Conglomerate.
2
[22 marks]
(2)
(2)
(2)

A. The following code has memory leaks because it allocates memory dynamically for each row of the matrix using "new" keyword.

B. We need to free the memory that has been allocated using "delete" keyword.

A - The following code has memory leaks because it allocates memory dynamically for each row of the matrix using "new" keyword, but it does not free the allocated memory using "delete" keyword. This can lead to memory leakage in the program.

B - To fix the problem, we need to free the memory that has been allocated using "delete" keyword. We can add a loop at the end of the function to iterate through each row of the matrix and delete the allocated memory using "delete" keyword. The correct code for the function buildMatrix would be:

void buildMatrix(int *matrix, int m, int n) {

int init = 10;

matrix = new int[m];

for(int i = 0; i < m; i++) {

matrix[i] = new int[n];

for(int j = 0; j < n; j++) {

matrix[i][j] = init;

init++;

}

}

// Free the allocated memory

for(int i = 0; i < m; i++) {

delete [] matrix[i];

}

delete [] matrix;

}

Learn more about memory leaks here https://brainly.com/question/30019797

#SPJ4

The value of arr that could be used to show that the method does not work as intended is:

int[][] arr = {{1, 2, 3}, {4, 5, 6}, {7, 8, 0}};

This value of arr can be used to show that the method does not work as intended because the method is supposed to return true if 0 is found in its two-dimensional array parameter arr. However, in this case, the method will throw an ArrayIndexOutOfBoundsException.

This is because the for loop that iterates over the rows of the array is using the <= operator instead of the < operator. This means that the loop will try to access an index that is one greater than the last valid index of the array, causing an ArrayIndexOutOfBoundsException.

To fix this issue, the for loop that iterates over the rows of the array should use the < operator instead of the <= operator:

for (int row = 0; row < arr.length; row++)

With this change, the method will correctly return true if 0 is found in its two-dimensional array parameter arr and false otherwise.

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

Ethanol production from sugarcane is comprised by the following steps: cleaning of sugarcane and extraction of sugars; juice treatment, concentration and sterilization; fermentation; distillation and dehydration.

The pull force necessary on the rope to reduce the pressure of the liquid trapped inside a piston cylinder device to 76 kPa is 1.18 kN, expressed to three significant figures.

To determine the pull force necessary on the rope to reduce the pressure of the liquid trapped inside a piston cylinder device to 76 kPa, we can use the equation:

F = (P1 - P2) * A

where F is the force, P1 is the outside pressure, P2 is the pressure inside the piston, and A is the area of the piston.

Given that the outside pressure is 100 kPa, the pressure inside the piston is 76 kPa, and the diameter of the piston is 0.25 m, we can calculate the area of the piston as:

A = π * (d/2)2 = π * (0.25/2)2 = 0.0491 m2

Plugging in the values into the equation, we get:

F = (100 - 76) * 0.0491 = 1.18 kN

Learn more about The pull force:

https://brainly.com/question/24791348

#SPJ11

Answer:

  see bold numbers below

Explanation:

Given the attached series-parallel circuit, you want to know ...

The circuit impedance is the sum of the series resistance and the parallel combination of the 1Ω resistor and the 3 mH inductor. For ω = 333, the inductor's impedance is Xl = jωL = j(333)(.003)Ω = j0.999Ω.

The total impedance is the sum ...

  Ztot = 10 + 1/(1/1 +1/j0.999) = 10.51∠2.73°

The total current in the circuit is ...

  Is = Vs/Ztot = 10∠45°/10.51∠2.73° = 0.9513∠42.27°

The branch currents are in reverse proportion to the branch impedance

  Ir = Is(Xl/(1+Xl)) = 0.6724∠87.30°

  Il = Is(1/(1+Xl)) = 0.6730∠-2.70°

Expressed as a sine function, these have the magnitude and phase angle indicated by the phasor:

  Is(t) = 0.9513·sin(333t +42.27°)

  Ir(t) = 0.6724·sin(333t +87.30°)

  Il(t) = 0.6730·sin(333t -2.70°)

At t=0, each of these current values is the magnitude of the current multiplied by the sine of the phase angle. In effect, it is the imaginary part of the current when it is expressed in complex form.

  Is(0) = 0.9513·sin(42.27°) = 0.6399 A

  Ir(0) = 0.6724·sin(87.30°) = 0.6716 A

  Il(0) = 0.6730·sin(-2.70°) = -.0317 A

__

Additional comment

Solving these problems is immensely aided by a calculator that easily handles complex numbers. The one shown in the attachments does not thread polar conversions over a list, but otherwise works nicely for this problem. Angle mode is set to degrees. The value of x is 0.999i.

To disable the textbox if the radio button is not checked and enable the textbox if the radio button is checked, we can use the `checked` property of the radio button and the `disabled` property of the textbox. Here is the code:

```html
if (priceRadioButton.checked) {
 priceTextBox.disabled = false;
} else {
 priceTextBox.disabled = true;
}
```

This will check the `checked` property of the `priceRadioButton` and if it is `true`, it will set the `disabled` property of the `priceTextBox` to `false`, enabling the textbox. If the `checked` property of the `priceRadioButton` is `false`, it will set the `disabled` property of the `priceTextBox` to `true`, disabling the textbox.

Learn more about radio button control:

https://brainly.com/question/29557793

#SPJ11

The tank has a total volume of 1.78 m3, of which one third is in the liquid phase, and the remaining two thirds are in the vapour phase. The system has a density of 287.6 kg/m3.

Density is the measurement of how tightly a substance is packed. It has such definition since it is the mass per unit volume. The density symbol is D, and the density formula is The formula is: = m/V when is the density, m is the object's mass, and V is its volume.

Volume of vapor = (2/3) x 1.78 = 1.1867 m^3

Volume of liquid = (1/3) x 1.78 = 0.5933 m^3

To determine the density, we need to find the mass of the vapor and the mass of the liquid..

Mass of vapor = Volume of vapor / Specific volume of vapor = 1.1867 m^3 / 0.08609 m^3/kg = 13.785 kg

Mass of liquid = Volume of liquid / Specific volume of liquid = 0.5933 m^3 / 0.001190 m^3/kg = 498.3 kg

The total mass of the system is the sum of the mass of the vapor and the mass of the liquid:

Total mass = Mass of vapor + Mass of liquid = 13.785 kg + 498.3 kg = 512.085 kg

Finally, we can calculate the density using the total mass and the total volume of the system:

Density = Total mass / Total volume = 512.085 kg / 1.78 m^3 = 287.6 kg/m^3

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

Two categories of laser printers are personal and shared. Personal laser printers are designed for individual use, typically in a home or small office setting.

Shared laser printers are designed for use by multiple people in a larger office setting. It is important to note that the terms "active-matrix" and "passive-matrix" do not apply to laser printers, but rather to different types of LCD screens. "Thermal" and "ink-jet" are also not categories of laser printers, but rather different types of printers altogether. Laser printers use toner, rather than ink, to produce high-quality prints.

Learn more about matrix: https://brainly.com/question/2456804

#SPJ11

The theoretical fracture strength of the brittle material is estimated to be approximately 165.6 MPa when a stress of 1300 MPa is applied and fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and tip radius of curvature of 0.004 mm.

To estimate the theoretical fracture strength of a brittle material given the information provided, we can use Griffith's theory of brittle fracture. According to this theory, the fracture strength of a brittle material can be expressed as:

σ_f = (2Eγπa)^0.5

where σ_f is the fracture strength, E is the elastic modulus, γ is the surface energy per unit area, and a is the length of the elliptically shaped surface crack.

To calculate the fracture strength, we need to first determine the surface energy per unit area of the material. For glass, a typical value of surface energy is around 1 J/m^2.

Given the length of the elliptically shaped surface crack (a) is 0.29 mm, and the tip radius of curvature is 0.004 mm, we can calculate the crack area (A) as follows:

A = πab = π(0.29/2)(0.004)

A ≈ 5.67 x 10^-7 m^2

Next, we can calculate the elastic modulus (E) of the material. For glass, the elastic modulus is typically around 70 GPa.

Substituting these values into the equation for fracture strength, we get:

σ_f = (2Eγπa)^0.5 = [2(70 x 10^9)(1)(π)(0.29 x 10^-3)]^0.5

σ_f ≈ 165.6 MPa

Learn more about theoretical fracture strength at: https://brainly.com/question/13707729

#SPJ11

The cdf of the amount of time a book on two-hour reserve is actually checked out can be represented by the function F(x) = P(X ≤ x), where X is the random variable representing the amount of time the book is checked out and x is a specific value of time.

If the cdf is given as f(x), we can find the probability that the book is checked out for a specific amount of time by evaluating the function at that value of x. For example, if we want to find the probability that the book is checked out for less than or equal to one hour, we would evaluate f(1) to get the probability.

Similarly, if we want to find the probability that the book is checked out for more than one hour but less than or equal to two hours, we would evaluate f(2) - f(1) to get the probability.

It is important to note that the cdf, F(x), gives the probability that the book is checked out for less than or equal to a specific amount of time, while the pdf, f(x), gives the probability density at a specific amount of time. The pdf can be found by taking the derivative of the cdf, F'(x) = f(x).

Learn more about The pdf:

https://brainly.com/question/29454290

#SPJ11

We determine the questions, according to the numerical properties:

(a) To find P1, we need to use the formula for force applied to a cantilever beam with a point load at the end:
P1 = (3EI/s)L
Where E is the modulus of elasticity, I is the moment of inertia, s is the gap, and L is the length of the beam. Plugging in the given values, we get:
P1 = (3(30x10^6)(0.196)(12))/0.25 = 84.48 kips
After the pin is inserted and P1 is removed, the reaction forces at the supports are equal and opposite to the applied force, so RA = -P1/2 = -42.24 kips and RB = P1/2 = 42.24 kips.

(b) To find P2, we need to use the same formula but with the length of Pipe 2 instead of Pipe 1:
P2 = (3EI/s)L
P2 = (3(30x10^6)(0.196)(8))/0.25 = 56.32 kips
After the pin is inserted and P2 is removed, the reaction forces at the supports are equal and opposite to the applied force, so RA = -P2/2 = -28.16 kips and RB = P2/2 = 28.16 kips.

(c) The maximum shear stress in the pipes occurs at the supports and is equal to the reaction force divided by the cross-sectional area of the pipe. For Pipe 1, the maximum shear stress is RA/A = (-42.24 kips)/(π(2.5^2 - 2^2)) = -10.72 ksi. For Pipe 2, the maximum shear stress is RB/A = (28.16 kips)/(π(2.5^2 - 2^2)) = 7.15 ksi.

(d) To find the temperature increase required to close the gap, we need to use the formula for thermal expansion:
ΔL = αLΔT
Where ΔL is the change in length, α is the coefficient of thermal expansion, L is the original length, and ΔT is the temperature change. Rearranging the formula and plugging in the given values, we get:
ΔT = (s)/(αL) = (0.25)/(11.7x10^-6)(12) = 1785.47°F
After the pin is inserted, the reaction forces at the supports are equal and opposite to the thermal expansion force, so RA = -P1/2 = -42.24 kips and RB = P1/2 = 42.24 kips.

(e) When the structure cools back to the original ambient temperature, the reaction forces at the supports will be zero because there is no longer any thermal expansion force. So RA = 0 kips and RB = 0 kips.

Learn more about numerical properties:

https://brainly.com/question/28210762

#SPJ11

The diffraction pattern of a lattice is determined by the Bragg's law, which states that nλ = 2d sin θ, where n is the order of diffraction, λ is the wavelength of the incident beam, d is the lattice spacing, and θ is the angle of incidence. For a 2D triangular lattice with a lattice spacing of 0.15 nm in the x-direction, the diffraction pattern will have three lowest orders corresponding to n = 1, 2, and 3.

The diffraction pattern for an isosceles triangle lattice with a height equal to its base will also have three lowest orders, but the angles of incidence will be different due to the different lattice spacing. The energy of the incident beam also affects the wavelength of the beam and therefore the diffraction pattern. A higher energy beam will have a shorter wavelength and will produce a different diffraction pattern than a lower energy beam.

Learn more about diffraction pattern

https://brainly.com/question/24305019

#SPJ11

Answer:

I need help also

Answer 1: The correct answer is B: CAD as it is used to describe 3D modeling programs that are used in fields that require precise and exact real-world measurements

CAD stands for Computer-Aided Design, which is used in fields such as construction, manufacturing, and engineering to create 2D or 3D models of products, buildings, and machines. These programs allow for precise measurements and calculations, making them essential in these industries where accuracy is critical.

Answer 2: The correct answer is A: To maintain safety and production quality. In the automotive industry, precise 3D modeling is necessary to ensure the safety of the vehicle and its occupants. The models must accurately represent every aspect of the car's design, from the smallest component to the overall structure. If the models are not precise, it could lead to production errors or safety hazards.

Answer 3: The correct answer is D: Wheel Physics. In the automotive industry, designers need to create 3D models of the vehicle that accurately represent the physics of its movement. This includes factors such as acceleration, braking, and steering, which are critical to the car's performance. Wheel physics is one such feature that would be helpful in this context.

Answer 4: The correct answer is A: CAD. CAD programs are commonly used in the construction industry to create 2D or 3D models of buildings and infrastructure. These programs allow designers to visualize the building's structure and layout, as well as its electrical, plumbing, and heating needs. This can help to identify potential design flaws, streamline construction processes, and ensure that the final product meets safety and quality standards.

Read more about 3D modeling here:

https://brainly.com/question/27512139

#SPJ1

The maximum shear stress that develops under uniaxial tension when the material reaches its uniaxial tensile yield strength is 52.8 MPa.

This is lower than the octahedral shear stress at this point (81.1 MPa), which indicates that the material is more likely to fail under the state of stress given in the question than under uniaxial tension.

According to the maximum distortion energy theory, the uniaxial tensile yield strength of the material can be determined using the following equation:

σy = √[(σ1-σ2)^2 + (σ2-σ3)^2 + (σ3-σ1)^2]/√2

Where σ1, σ2, and σ3 are the principal stresses.

In this case, the principal stresses are:

σ1 = 40 MPa
σ2 = 50 MPa
σ3 = -60 MPa

Plugging these values into the equation gives:

σy = √[(40-50)^2 + (50-(-60))^2 + (-60-40)^2]/√2

σy = √[100 + 12100 + 10000]/√2

σy = √[22200]/√2

σy = 105.5 MPa

Therefore, the uniaxial tensile yield strength of the material is 105.5 MPa.

The octahedral shear stress at this point can be determined using the following equation:

τoct = √[(σ1-σ2)^2 + (σ2-σ3)^2 + (σ3-σ1)^2]/3

Plugging in the same principal stresses gives:

τoct = √[(40-50)^2 + (50-(-60))^2 + (-60-40)^2]/3

τoct = √[100 + 12100 + 10000]/3

τoct = √[22200]/3

τoct = 81.1 MPa

Therefore, the octahedral shear stress at this point is 81.1 MPa.

To compare this octahedral shear stress with the maximum shear stress that develops under uniaxial tension when the material reaches its uniaxial tensile yield strength, we can use the following equation:

τmax = σy/2

Plugging in the uniaxial tensile yield strength gives:

τmax = 105.5/2

τmax = 52.8 MPa

Learn more about uniaxial tension:

https://brainly.com/question/13390917

#SPJ11

The vertical deflection of the bar at D can be determined by using the equation for deflection of a beam with a distributed load.

First, we need to calculate the moment of inertia (I) of the rod CB. The moment of inertia for a circular cross-section is given by:

I = (pi/4) * r^4

Where r is the radius of the cross-section. In this case, the cross-sectional area of the rod is 14mm^2, so we can calculate the radius as follows:

14mm^2 = (pi/4) * r^2

r = sqrt((14mm^2 * 4)/pi) = 2.12mm

Now we can calculate the moment of inertia:

I = (pi/4) * (2.12mm)^4 = 39.9mm^4

Next, we need to calculate the elastic modulus (E) of the 6061-T6 aluminum. The elastic modulus for this material is typically around 68.9 GPa (68.9 x 10^9 Pa).

Now we can use the equation for deflection of a beam with a distributed load to calculate the vertical deflection at D:

delta = (5/384) * (w * L^4)/(E * I)

Where delta is the vertical deflection, w is the distributed load, L is the length of the beam, E is the elastic modulus, and I is the moment of inertia. In this case, we have:

delta = (5/384) * (w * (0.8m)^4)/(68.9 x 10^9 Pa * 39.9mm^4)

Simplifying and converting units gives:

delta = (5/384) * (w * (800mm)^4)/(68.9 x 10^9 Pa * 39.9mm^4) = (1.05 x 10^-6) * w

Therefore, the vertical deflection of the bar at D is given by:

delta = (1.05 x 10^-6) * w

Where w is the distributed load in N/m.

Learn more about The vertical deflection of the bar:

https://brainly.com/question/17080885

#SPJ11

The FOUR characteristics of the magnetic lines of force are:

To supply a load that operates at 6 V using four 3 V cells, we can connect the cells in series to increase the total voltage. We can connect two sets of two cells in series, and then connect these two sets in parallel.

This will give us a total voltage of 12 V (3 V + 3 V + 3 V + 3 V) and a current capacity that is equal to the capacity of each individual cell. We can then use a voltage regulator or a resistor to drop the voltage to 6 V, and connect the load RL in series with the voltage regulator or resistor. The circuit diagram will look like:

[3 V]---[3 V]--[3 V]---[3 V]--|

+---[RL]---(voltage regulator or resistor)---|

|

[ground]--------------------------------------------------------------------|

Note that the cells are connected in series in pairs, and the pairs are connected in parallel. The load is connected in series with the voltage regulator or resistor.

Learn more about Magnetic Lines:
https://brainly.com/question/17011493
#SPJ1

The maximum allowable power for the silicon chip when it is flush mounted in a substrate with an unheated starting length of 20 mm is 0.136 W.

To find the maximum allowable power for the silicon chip, we need to use the equation for heat transfer from a flat plate in parallel flow:

q'' = h(Ts - T∞)

Where q'' is the heat flux, h is the heat transfer coefficient, Ts is the surface temperature, and T∞ is the free stream temperature.

We can rearrange this equation to find the maximum allowable power:

q'' = h(Ts - T∞)Pmax = q''A = hA(Ts - T∞)

Where Pmax is the maximum allowable power and A is the area of the chip. We are given the values for u∞, T∞, Ts, and A, so we can plug these into the equation to find Pmax:

u∞ = 20 m/s

T∞ = 24°C

Ts = 80°CA

= (10 mm × 10 mm)

= 0.0001 m²

We also need to find the value for h, which we can do using the equation for the Nusselt number for a flat plate in parallel flow:

[tex]NuL = 0.664Re^{0.5}Pr^0.33[/tex]

Where NuL is the Nusselt number, Re is the Reynolds number, and Pr is the Prandtl number. We can rearrange this equation to find h:

h = (NuLk)/where k is the thermal conductivity and L is the length of the chip. We can find the values for Re and Pr using the equations:

Re = (u∞L)/νPr = (Cpμ)/k

Where ν is the kinematic viscosity, Cp is the specific heat capacity, and μ is the dynamic viscosity. We can find the values for these properties using the given values for u∞ and T∞ and looking up the properties of air at these conditions:

ν = 15.68 × 10^-6 m²/s

Cp = 1007 J/kg·Kμ

= 18.46 × 10^-6 kg/m·sk

= 0.02624 W/m·K

We can now plug these values into the equations to find Re, Pr, NuL, and h:

Re = (20 m/s × 0.01 m)/(15.68 × 10^-6 m²/s)

= 12755.1Pr =

(1007 J/kg·K × 18.46 × 10^-6 kg/m·s)/(0.02624 W/m·K)

= 0.708NuL

= 0.664(12755.1^0.5)(0.708^0.33)

= 59.58h

= (59.58 × 0.02624 W/m·K)/0.01 m

= 155.6 W/m²

We can now plug these values into the equation for Pmax to find the maximum allowable power:

Pmax = (155.6 W/m²·K)(0.0001 m²)(80°C - 24°C) = 0.874 W

We can use the equation for the Nusselt number for a flat plate with an unheated starting length:

NuL = 0.3387(ReLPr)^(1/3)

Where L is the length of the heated portion of the plate.

We can plug in the values for Re, Pr, and L to find NuL:

NuL = 0.3387(12755.1 × 0.01 m × 0.708)^(1/3)

= 9.23

We can now use this value for NuL to find a new value for h:

h = (9.23 × 0.02624 W/m·K)/0.01 m = 24.25 W/m²·

We can now plug this value for h into the equation for Pmax to find the maximum allowable power:

Pmax = (24.25 W/m²·K)(0.0001 m²)(80°C - 24°C)

= 0.136 W

To learn more about Power :

https://brainly.com/question/30817666

#SPJ4

Engineers apply their knowledge of mathematics and science to solve real-world problems, mathematicians develop and prove new mathematical theories and principles, and scientists use the scientific method to study the natural world and understand phenomena.

Engineers use their knowledge of mathematics and science to design and build practical solutions to real-world problems. They apply their knowledge of physics, chemistry, and mathematics to design, develop, test, and improve products, systems, and processes. They focus on the application of theories and principles to develop practical solutions that meet specific needs or goals.

Mathematicians, on the other hand, use their expertise in mathematics to study abstract concepts, develop new theories, and prove mathematical theorems. They focus on the development of mathematical theories and principles that can be applied to a wide range of fields, including engineering, physics, and computer science. Their work often involves developing new algorithms, models, and methods that can be used to solve complex problems.

Scientists use the scientific method to study the natural world, understand phenomena, and test hypotheses. They use a wide range of tools and techniques to gather data, analyze it, and draw conclusions. Their work often involves designing experiments, conducting observations, and developing models to explain natural phenomena. Scientists focus on understanding the underlying principles that govern the behavior of the natural world.

For more such questions on Engineers, click on:

https://brainly.com/question/30353036

#SPJ11

The rate of heat transfer from the pipe will increase when the insulation is taken off if the outer radius of the insulation is less than the critical radius. This is because the critical radius of insulation is the radius at which the rate of heat transfer is minimized.

When the insulation radius is less than the critical radius, the rate of heat transfer is actually higher than it would be without any insulation at all. Therefore, removing the insulation will increase the rate of heat transfer from the pipe for the same pipe surface temperature.

The critical radius of insulation can be calculated using the following formula:

[tex]r_c = k/h[/tex]

Where [tex]r_c[/tex] is the critical radius of insulation, k is the thermal conductivity of the insulation, and h is the heat transfer coefficient of the fluid surrounding the pipe. If the outer radius of the insulation is less than this critical radius, then removing the insulation will increase the rate of heat transfer.

This can be seen graphically as well, where the rate of heat transfer is plotted against the insulation thickness. The graph will show a minimum at the critical radius, and any insulation thickness less than this will result in a higher rate of heat transfer.

Learn more about insulation

https://brainly.com/question/18598066

#SPJ11

The approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A is 5237692500 J/m³.

To calculate the approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A, follow these steps:

1. Calculate the power of the welding operation:

Power = Voltage × Current

Power = 25 V × 200 A = 5000 W

2. Determine the specific heat capacity of mild steel. The specific heat capacity of mild steel is approximately 450 J/kg·K.

3. Calculate the mass of mild steel per unit volume. The density of mild steel is approximately 7850 kg/m³.

4. Calculate the energy required to heat 1 kg of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 450 J/kg·K × 1 kg × (1776 K - 293 K)

Energy = 450 J/kg·K × 1 kg × 1483 K

Energy = 667350 J/kg

5. Calculate the energy required to heat 1 m³ of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 667350 J/kg × 7850 kg/m³

Energy = 5237692500 J/m³

Learn more about Energy:

https://brainly.com/question/25737117

#SPJ11

In a Maxwell element, the stress and strain are directly proportional to each other. This means that as the stress increases, the strain also increases at the same rate.

Therefore, the strain time history for a Maxwell element will look exactly like the stress time history, just scaled by a factor of the modulus of elasticity. In a Kelvin element, the stress and strain are not directly proportional to each other. Instead, the strain will lag behind the stress, and will have a more gradual increase and decrease. This means that the strain time history for a Kelvin element will look similar to the stress time history, but with a smoother curve and less sharp peaks and valleys.

To draw the strain time history for each of these elements, simply plot the stress time history on the x-axis and the strain on the y-axis. For the Maxwell element, the strain will be equal to the stress divided by the modulus of elasticity. For the Kelvin element, the strain will be equal to the stress divided by the modulus of elasticity, but with a time delay factor added in. This time delay factor will cause the strain to lag behind the stress and have a more gradual increase and decrease.

Learn more about Maxwell element:

https://brainly.com/question/30480107

#SPJ11

The block has shrunk by about 45.3% based on the volume change, which is -0.453 times the initial volume.

The expression's negative sign indicates how the excessive pressure applied caused the material's volume to shrink. In other words, a decrease in volume will result from an increase in pressure. The volume change will be negative if pressure P is positive.

ΔV/V = -3K ΔP

K = E/(3(1-2v))

Given:

[tex]E = 60 GPa = 60 x 10^9 Pa[/tex]

v = 0.25

a = 100 mm = 0.1 m

b = 50 mm = 0.05 m

c = 60 mm = 0.06 m

F1 = 1801 N

F2 = 50 kN = 50000 N

F3 = 100 kN = 100000 NF_total = F1 + F2 + F3

F_total = 1801 N + 50000 N + 100000 N

F_total = 151801 NΔP = F_total / (abc)

ΔP = 151801 N / (0.1 m x 0.05 m x 0.06 m)

[tex]ΔP = 5.0337 x 10^7 Pa[/tex]

Finally, we can calculate the fractional change in volume using the formula:

ΔV/V = -3K ΔP

[tex]K = E/(3(1-2v)) = 60 x 10^9 Pa / (3(1-2(0.25))) = 6.0 x 10^10 Pa[/tex]

[tex]ΔV/V = -3(6.0 x 10^10 Pa) (5.0337 x 10^7 Pa)[/tex]

ΔV/V = -0.453

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

It can help engineers identify problems by recognizing when systems are working with each other. Systems often interact with one another, so it is important for engineers to understand the dynamics of these systems in order to recognize any potential issues or problems. Additionally, this understanding can lead to improved innovation in engineering, as engineers can identify what works and what does not work between systems.

The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems.

How does the fact that systems often work with other systems affect engineering?

Engineering is a vast field that encompasses a wide range of subfields and specializations. Engineers are professionals who specialize in the design, construction, and maintenance of systems that are critical to the smooth running of society. They are also responsible for developing solutions to complex problems that affect individuals, communities, and the environment. Systems engineers work on projects that involve complex systems with interdependent components.

As a result, they need to be able to think critically, solve problems, and collaborate with other professionals to achieve their goals. The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems. When systems interact, they create a complex web of interdependencies that can be difficult to understand. Systems engineers need to be able to identify these interdependencies and analyze the system as a whole. This can be challenging, but it is also rewarding when a solution is found.

How does the fact that systems often work with other systems : https://brainly.com/question/17489470

#SPJ11

The ultimate tensile stress in MPa is 156.823 MPa and the shear stress in MPa is 155.146 MPa.

The ultimate tensile stress can be found by dividing the tensile peak load by the cross-sectional area of the specimen. The cross-sectional area of a circular specimen is given by πr^2. The stress in MPa can be found by dividing the stress in N/m^2 by 10^6.

a) The ultimate tensile stress in MPa is:

Ultimate tensile stress = (Tensile peak load) / (Cross-sectional area)

= (4281 N) / (π(2.95 mm)^2)

= (4281 N) / (27.298 mm^2)

= 156.823 N/mm^2

= 156.823 MPa

b) The shear stress in MPa is:

Shear stress = (Shear force) / (Cross-sectional area)

= (4100 N) / (π(2.9 mm)^2)

= (4100 N) / (26.423 mm^2)

= 155.146 N/mm^2

= 155.146 MPa

Learn more about MPa:

https://brainly.com/question/30587466

#SPJ11

To gather the necessary input from the user to complete the story, we will need to create variables that will store the input from the user. It is important to be mindful of which data types to use for each variable. For string input, we should use `getline` instead of just `cin` by itself.

Here is an example of how to create the variables and gather the input from the user:

```cpp
// Declare variables
string name;
int age;
char gender;

// Get input from user
cout << "Enter your name: ";
getline(cin, name);
cout << "Enter your age: ";
cin >> age;
cout << "Enter your gender (M/F): ";
cin >> gender;
```

In this example, we have created three variables: `name` (string), `age` (int), and `gender` (char). We then use `getline` to get the string input from the user for the `name` variable, and `cin` to get the int and char input for the `age` and `gender` variables.

Remember to always be mindful of the data types you are using for each variable, and to use `getline` for string input to ensure that the entire string is captured.

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

Both technicians A and B are correct. The low-impedance test light and the noid light are both used to verify the existence of an injector pulse.

What is a low-impedance test light?A low-impedance test light is a tool that can be used to detect an injector pulse. This device can be used to check for voltage drops that can prevent the fuel injectors from functioning correctly.What is a noid light?A noid light is a tool that is used to check for injector pulses. This device is installed in the electrical circuit between the fuel injectors and the vehicle's computer, and it illuminates when the fuel injectors are receiving power.What is an injector pulse?

An injector pulse is a brief burst of current that flows to the fuel injector to activate it. This brief pulse of current is sufficient to open the injector and allow the fuel to flow into the combustion chamber for ignition.What is an injector?An injector is an electronic component that is used to deliver fuel to the engine. It is a type of valve that opens and closes to allow the fuel to flow into the combustion chamber when it is required.

Learn more about  injector pulse at: brainly.com/question/14278715

#SPJ11

The necessary velocity, temperature, and density of the airflow in the wind-tunnel test section are 1250 m/s, 89.2 K, and 2.07 kg/m3, respectively.

To calculate the necessary velocity, temperature, and density of the airflow in the wind-tunnel test section such that the lift and drag coefficients are the same for the wind-tunnel model and the actual airplane in flight, we need to use the concept of dynamic similarity. Dynamic similarity occurs when the forces acting on two systems are proportional to each other. This is achieved when the Reynolds number and the Mach number are the same for both systems.

Reynolds number (Re) = (ρVd)/μ

Mach number (Ma) = V/a

Where ρ is the density, V is the velocity, d is the characteristic length, μ is the dynamic viscosity, and a is the speed of sound.

Since the wind-tunnel model is one-fifth the size of the actual airplane, the characteristic length (d) for the model will be one-fifth the characteristic length of the actual airplane.

dmodel = (1/5)dairplane

To achieve dynamic similarity, we need to have the same Reynolds number and Mach number for both systems.

Reairplane = Remodel

(ρairplaneVairplanedairplane)/μairplane = (ρmodelVmodeldmodel)/μmodel

Similarly, we need to have the same Mach number for both systems.

Maairplane = Mamodel

Vairplane/aairplane = Vmodel/amodel

Using the given values and the equations above, we can calculate the necessary velocity, temperature, and density of the airflow in the wind-tunnel test section.

ρmodel = (ρairplaneVairplanedairplaneμmodel)/(Vmodeldmodelμairplane)

Tmodel = (TairplaneVairplane^2)/(Vmodel^2)

Vmodel = (Vairplaneaairplane)/amodel

Plugging in the given values:

ρmodel = (0.414 kg/m3)(250 m/s)(10 km)(1.01x10^5 N/m2)/(Vmodel)(1/5)(10 km)(1.01x10^5 N/m2)

Tmodel = (223 K)(250 m/s)^2/(Vmodel^2)

Vmodel = (250 m/s)(√(287 J/kg-K)(223 K))/(√(287 J/kg-K)(Tmodel))

Solving for Vmodel, Tmodel, and ρmodel, we get:

Vmodel = 1250 m/s

Tmodel = 89.2 K

ρmodel = 2.07 kg/m3

Therefore, the necessary velocity, temperature, and density of the airflow in the wind-tunnel test section are 1250 m/s, 89.2 K, and 2.07 kg/m3, respectively.

Learn more about velocity

https://brainly.com/question/24445340

#SPJ11

The temperature of the tank after a 45-min period is estimated to be 30.908 K.

Temperature is a measure of how hot or cold something is relative to a standard reference point. It is typically measured in degrees Celsius (°C), Kelvin (K), or Fahrenheit (°F).

The rate of heat transfer can be estimated by using the following equation: Q = hA∆T

From the given data, the surface area of the tank is calculated as:

A = πr2 = π (0.25 m)2 = 0.19625 m2

The heat transfer coefficient for a windy environment can be estimated by using the following equation: h = 0.024V1/2, where V is the wind speed (m/s).

From the given data, the wind speed is calculated as: V = 40 km/h = 11.1 m/s

Therefore, the heat transfer coefficient is calculated as: h = 0.024 (11.1)1/2 = 0.92 W/m2K

The temperature difference between the air and the tank is calculated as:  ∆T = (Tair – Ttank) = (288 K – 308 K) = -20 K

Therefore, the rate of heat transfer is calculated as:

Q = hA∆T = (0.92 W/m2K) (0.19625 m2) (-20 K) = -3.7 W

Since the tank is losing heat, the rate of heat transfer is negative.

From the given data, the mass of the water in the tank is calculated as:

m = ρV = (1,000 kg/m3) (0.095 m3) = 95 kg

The specific heat capacity of water is assumed to be 4,186 J/KgK.

Therefore, the temperature difference is calculated as:

∆T = Q/(mc) = (-3.7 W)/ [(95 kg) (4,186 J/KgK)] = -0.0089 K

Therefore, the temperature of the tank after a 45-min period is estimated to be 30.908 K.

To learn more about temperature

https://brainly.com/question/15969718

#SPJ1

Answer:    

Explanation: